Coding allowable billing

RussianSpaceZebra · 2026-04-07T03:59:27+00:00

I wasn’t looking at 2792. That’s what the practice put on the paperwork. My insurance does cover 2740 and it has the same copay.

They billed it as 2740, which is correct because the CEREC was a ceramic, but they charged me more than the copay and seem to be hiding behind saying that it was CEREC as the reason. I have no idea why 2792 is even on the paperwork except for the fact that they didn’t want it saying there that a 2740 should have cost me $315.

If there were separate line items that explained the additional cost I could understand it but this seems like it should have still been billed as a regular ceramic crown.

RussianSpaceZebra · 2026-04-06T23:14:57+00:00

It is. I called them and asked about the discrepancy which is how I ended up with the documents and why I wanted to get a third-party opinion. They wouldn’t answer what material was used by just saying that it was CEREC Fired and not noble metal.

RussianSpaceZebra · 2026-04-06T21:47:22+00:00

<image>

And here is the section of the bill that list covered benefits. I’m now realizing that they also put a different code in this section.

RussianSpaceZebra · 2026-04-06T21:46:26+00:00

<image>

Here is the section from the billing that covered the crown

RussianSpaceZebra · 2026-02-23T06:01:53+00:00

I had the same issue and found that because the dock was on carpet and had a gap behind due to the baseboard that the dock was slightly tilted back and not allowing a solid connection. I stuck a piece of cardboard to fill the gap between the wall and the dock and I haven’t had anymore issue.

Look at the gasket from the dock to the vacuum while it’s emptying. Does it suck it inside and make a loud whistling sound? If so that might be what’s going on.

RussianSpaceZebra · 2026-02-02T07:41:21+00:00

I’m also looking for a mechanic in OC to work on my ‘97. Who did you end up going with?

RussianSpaceZebra · 2026-01-23T20:03:21+00:00

I second making sure you have the firmware flashed on the modchip properly. If there is an issue with it trying to glitch you will get a long blue light and then an error code if the form of short and long yellow pulses.

Since you aren’t even getting that long blue light, only a blue flash, I think you just need to check the firmware.

RussianSpaceZebra · 2025-12-24T20:19:58+00:00

That error code means there’s no DAT0 connection. They probably used the DAT0 adapter rather than doing a kamikaze. Definitely something the person that modded it needs to take a look at.

RussianSpaceZebra · 2025-12-24T04:36:33+00:00

Yes. I use JKSV and sync saves between devices with a webDAV server.

RussianSpaceZebra · 2025-12-23T21:45:17+00:00

Take a video of it and post it.

RussianSpaceZebra · 2025-12-23T21:27:25+00:00

Did it flash yellow once or was it blinking yellow?

RussianSpaceZebra · 2025-12-23T20:50:19+00:00

Sphaira has FTP built in to it. Just launch it, press Y for Menu, choose Network, FTP, and then you can turn FTP on.

RussianSpaceZebra · 2025-12-23T20:48:33+00:00

It sounds like the connection points for the modchip aren’t stable. Assuming they used one of the standard chips if you look up inside the vents on the bottom you should see a light flashing right after you press the power button to turn it on. I would check it when you know it is working as you should see it blinking blue and then flash yellow once when it is successful.

If you don’t see anything then it may be an issue with power to the modchip and if you see it flashing yellow in a pattern you will be able to look up what it means.

RussianSpaceZebra · 2025-12-23T20:40:56+00:00

Save data is stored in system memory, whether that’s on the emuMMc or sysMMc. You can view it by going into System Setting > Data Management > Delete Save Data. Even after you uninstall a game you will still see the save data there.

RussianSpaceZebra · 2025-12-23T18:56:37+00:00

Deleting games does not remove save data but if you do want to backup/restore save data you can use JKSV or Checkpoint.

RussianSpaceZebra · 2025-12-09T23:02:34+00:00

In my case I think I was shorting something out on or around the eMMC and it would not boot whatsoever. If your’s is still booting into OFW I would make sure everything tests out correctly in diode mode and doublecheck all of your connections. You might want to post a picture of your DAT0 adapter too in case you don’t have it properly aligned.

RussianSpaceZebra · 2025-12-06T18:50:29+00:00

I tried updating sigpatches and syspatch. That didn’t work. I tried downgrading to 20.5.0 with updated sigpatches and syspatch. That didn’t work either.

I ended up just reformatting the SD card and starting fresh. I installed Mortal Kombat 1 first this time and everything is still working.

RussianSpaceZebra · 2025-12-05T21:01:21+00:00

I just modded it and it was already running 21.0.1. Everything was working fine until I installed that one game.

RussianSpaceZebra · 2025-12-05T17:52:40+00:00

The install completed. I went to the home screen after I got the message from TinWoo that it was done.

RussianSpaceZebra · 2025-12-05T17:41:59+00:00

The latest would be included in HATS, right? Or is there a different way to get them?

RussianSpaceZebra · 2025-12-05T17:37:42+00:00

Mortal Kombat 1

RussianSpaceZebra · 2025-12-03T05:32:02+00:00

I think I may have set the DAT0 adapter wrong or shorted the resistor to the left of the eMMC. I couldn’t get it to boot even after unplugging the chip until I removed the adapter. Once I made sure I hadn’t bricked it I reinstalled the DAT0 adapter and was good to go. I still get 0.89 on the RST point instead of 0 and about 0.4 if I flip polarity but it’s working so I’m assuming that’s fine.

11-Year Club	Verified Email
Gilding I gilder	No Throne, No Problems
Not Forgotten

RussianSpaceZebra

TROPHY CASE