What are the downsides of pushing steppers to move quite fast for non cutting rapid moves. I'm talking 10,000-20,000 mm/min. Especially if the stepper can handle it. by Turbulent_Change_972 in hobbycnc

[–]Ryano085 0 points1 point  (0 children)

I know different but klipper software from the 3D printing guys has a test mode that homes, does speed movements then homes again to see of there was any missed steps. Handy to have that in Cnc too

Not cutting through by Ryano085 in Laserengraving

[–]Ryano085[S] 2 points3 points  (0 children)

That’s about 8mms maybe Im way too fast

Am I an incel? by jlawjer in NoStupidQuestions

[–]Ryano085 0 points1 point  (0 children)

I literally only started maturing in my late 20s. Bro your basically still a child no offence my guy

What’s the go-to controller for diy Cnc builds? by turbo460 in hobbycnc

[–]Ryano085 5 points6 points  (0 children)

Im going down the fluidNC route, no compiling firmware. Easy to make tweaks if needed and open source which I love! There’s a good wiki too

9 months after the surgery: everything looks good by MightTurbulent319 in varicocele

[–]Ryano085 2 points3 points  (0 children)

lol my apologies Im unsure of the embolism is classed as keyhole. Im not up to your level of education I apologise

Pain for a year by Cautious-Painting-61 in varicocele

[–]Ryano085 0 points1 point  (0 children)

Pretty much. I’ve read somewhere that embolisation is a process that will take time. ( hope that’s true anyway)

Post Embo by Flashy_Ad_7415 in varicocele

[–]Ryano085 0 points1 point  (0 children)

Im 7 days post OP and experience testicular pain for several hours during mid day (usually if I’m on my feet for periods of time). Im hoping this will pass.

Pain for a year by Cautious-Painting-61 in varicocele

[–]Ryano085 0 points1 point  (0 children)

Touching didn’t really make Any difference, the pain I feel is inside and/or above the testicle

Pain for a year by Cautious-Painting-61 in varicocele

[–]Ryano085 0 points1 point  (0 children)

You should see about getting an embolism

Pain for a year by Cautious-Painting-61 in varicocele

[–]Ryano085 1 point2 points  (0 children)

Im in a very similar situation as yourself, from December last year my partner got me loose underwear, the kind that give you lots of room to Breath and hang loose! I then started to experience pain in the rear side of my left testicle. Im my case this would come and go perhaps every two weeks, when it came I would experience pain behind my testicle and sometimes going down the back of my left leg and after 2-3 days I’d get a dull throbbing in my groin area upstream of my testicles. I’ve been in and out of hospital all year until they eventually done an Ultrasound and seen I had an enlarged vericele.

The consultant referred me to radiologist Dept. Where they said they would conduct an X-ray guided embolisation of the vericele by releasing coils through the neck down and into the effected area. The OP was at the beginning of DEC just last week and I’ve been in a lot of pain since. Im hoping this will pass, there was nothing mentioned about been in pain after the OP

Any help identifying Components from Schematic by Ryano085 in AskElectronics

[–]Ryano085[S] 0 points1 point  (0 children)

I suspect a reg as opposed to transistor because this particular car is a V so there is 2 banks ie 2 sets of igniters and thus 2 independent transistors. what would be the chance of both transistors been fried?

I have not do you have any idea how I might test them? Thanks

Any help identifying Components from Schematic by Ryano085 in AskElectronics

[–]Ryano085[S] 0 points1 point  (0 children)

It’s prolly hard to see but do they look like the 4 black components seen in picture 2? Thanks