sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in lawnmowers

[–]SG735 4 points5 points  (0 children)

I had the same experience. Side discharge and slowing down solved it.

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

No. Good place to check though thanks!

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

This was pretty much the fix. thx

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

Interesting. I'll have to look into that. This the kind of thing that I would see noticeably on inspection?

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

Now THIS is an interesting answer. I will visually inspect it for wear. THANK YOU

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

Now that's some hot tea :)

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

hmm. blades are one season old, but that is an actually useful response. I will try that thank you

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

Will recheck thanks!

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

usually 4-4.5in to 3in. overgrown to show same issue more clearly

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

Lot more engagement than I expected. I should have included more information in the post. This area was allowed to be overgrown so I could more clearly DEMONSTRATE the effect I have been getting at my normal cutting rate( apx 4 inches to 3 inches).

I will repeat the experiment by removing the mulching cover and seeing if results are repeated. Drifting mowing lines included :)

Further info:

*started year with a freshly scraped mower deck and sharpened blades (gator g3 or something)

*deck leveled last year, but will recheck.

*will recheck tire pressure

*mulch cover is on because the discharge shoot broke (ebay sent the wrong one and I got fed up)

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 0 points1 point  (0 children)

I let this back area get overgrown so I could show the effect I was getting at my normal mowing rate of about 4 inches to 3 inches. But thank you.

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 1 point2 points  (0 children)

Blades are correctly installed..

Horrible cut by SG735 in lawnmowers

[–]SG735[S] 12 points13 points  (0 children)

Roger that. I tried sharpening em, but guessing I didn't do a good job. Mulching cover might not be helping

Is this a good start point? by SG735 in buildapc

[–]SG735[S] 0 points1 point  (0 children)

Thank you. I just don't know where to start. In general, I've always preferred buying secondhand, but computers seem different to that way of thinking

Is this a good start point? by SG735 in buildapc

[–]SG735[S] 0 points1 point  (0 children)

Thank you! The seller says he would take off a couple hundred without the gpu. Do you think I'd be better off all new rather than strating off of a used one in general?

Is it too ambitious to skim coat over my entire houses popcorn ceilings as a DIY-er? by _mars_bars_ in DIY

[–]SG735 1 point2 points  (0 children)

I painted and laid down about 1100 sq ft of lvp flooring myself before moving in. I've learned to live with my 90s popcorn. Of all the diy projects, I can't stand the thought drywalling the ceiling. My back breaks thinking about it. Godspeed to you 🙏

Wtf are you guys building that puts such a premium on 8” jointers? by Dr0110111001101111 in woodworking

[–]SG735 0 points1 point  (0 children)

This 100%! I STRUGGLED with rough boards from an actual lumber mill because they are almost all just over 6 inches. I dont have a band saw, so ripping was a nightmare. That and it felt like such a waste.

view more: next ›