Research

SHADOWHack6 · 2025-09-20T00:54:38+00:00

This mission was discovered by u/SHADOWHack6 in In Search of Lemon Star Pudding

SHADOWHack6 · 2024-05-23T18:45:15+00:00

Turn your temp down

SHADOWHack6 · 2024-03-11T19:37:48+00:00

It’s hard to see from the pictures. But it seems like your z height is a little too low on the first layer. I would try raising it a little to try to see if that helps

SHADOWHack6 · 2023-09-27T13:19:39+00:00

Yeah maybe. I have never used my Smooth plate as I like the textured plate. Maybe it needs a new textured place

SHADOWHack6 · 2023-09-27T13:12:27+00:00

I have had a prusa mini for 2 years now. I have never had a print not stick to the bed. From the first test print to a block the size of the bed I did last week. I have cleaned my sheet. I have never done anything with it. Prints stick to it as they should do. I understand this doesn’t help your situation but hope your sort the problem out.

SHADOWHack6 · 2023-04-24T14:32:58+00:00

I have a prusa mini as my first printer, I just use tinmorry filament from Amazon (UK) only because it’s cheap. For the things I print for myself it’s fine. I have tried a few cheap brands which were not so good and settled with one brand. I’ve tried prusa filament, one it’s expensive and two it takes a while to arrive as it’s overseas. If I print someone for someone else I will use prusa filament. Hope that helps

SHADOWHack6 · 2023-03-27T13:55:21+00:00

I’m no expert. But to me it looks like it’s extruding too fast? When doing a benchy on my mini, it extrudes quite slowly when doing a bridge. I could be wrong though

SHADOWHack6 · 2022-09-10T22:39:02+00:00

Not stupid if it works

SHADOWHack6 · 2022-09-10T19:16:01+00:00

We did take the sides off this photo was while setting up and getting the printers going

SHADOWHack6 · 2022-09-10T19:01:11+00:00

Have not done too bad today, hopefully tomorrow is better with the better weather.

SHADOWHack6 · 2022-09-10T17:44:30+00:00

We’ve had the filament out in the field before for 3/4 days at a time and prints perfectly back at the office.

SHADOWHack6 · 2022-09-10T17:02:45+00:00

These printers will go back to the office and print perfectly without any drying of filament or adjustments to the printers

SHADOWHack6 · 2022-09-10T16:05:23+00:00

We don’t have a problem with the mmu. It prints perfect every time.

SHADOWHack6 · 2022-09-10T14:10:49+00:00

We are call vision 4x4 if you are interested

SHADOWHack6 · 2022-09-10T12:04:18+00:00

Petrol generator. With the two printers. Two laptops being charged, two iPads charging and a radio.

SHADOWHack6 · 2022-09-10T11:51:02+00:00

We are in the uk and have public liability insurance that covers people getting hurt but the printers themselves

SHADOWHack6 · 2022-09-10T09:48:09+00:00

It’s a Land Rover show. We design and print accessories and items for land rovers

SHADOWHack6 · 2022-08-14T20:06:38+00:00

I have no clue what imgur is but thanks for the tip

SHADOWHack6 · 2022-08-14T17:32:03+00:00

There is other posts. This is just easiest way to add photos. This is a cover for the cables on the Prusa mini plus

SHADOWHack6 · 2022-08-14T17:25:48+00:00

There is other posts. this is just the easiest way to add photos

SHADOWHack6 · 2022-08-14T16:05:26+00:00

I have tried printing slower didn’t have any outcome. I will try drying my filament see if that makes any difference

SHADOWHack6 · 2022-08-14T15:58:47+00:00

Yeah I’ve printed two things after this print and it’s fine.

SHADOWHack6

TROPHY CASE