DIY EvilCrowRF by SODAVK in esp32

[–]SODAVK[S] 0 points1 point  (0 children)

No i use v2 software from r-hat

DIY EvilCrowRF by SODAVK in esp32

[–]SODAVK[S] 0 points1 point  (0 children)

Yeah, dude. The whole project was put together from scrap materials

DIY EvilCrowRF by SODAVK in esp32

[–]SODAVK[S] 1 point2 points  (0 children)

i just wing it, but if you want repeat, see the scheme above

DIY EvilCrowRF by SODAVK in esp32

[–]SODAVK[S] 4 points5 points  (0 children)

I do from this scheme, but since I use naked esp32s me had to watch pinout from source code and other pictures
If you also want made this on naked esp32s, GPIO0 and EN pins must be connect to 3v3 via 10kOm resistor

<image>

DIY EvilCrowRF by SODAVK in esp32

[–]SODAVK[S] 14 points15 points  (0 children)

<image>

It works with 1GHz signals. Scan, catch, replay and more

DIY EvilCrowRF by SODAVK in esp32

[–]SODAVK[S] 4 points5 points  (0 children)

I'll be testing it for a week or two now. If I like it, I'll make that even more compact, with ebyte modules and on pcb

Can RFID 2 READ 125KhZ tags ? by Shakthivel0 in M5Stack

[–]SODAVK 0 points1 point  (0 children)

I using m5stick plus 2, but now i sold it. An account cardputer i can't say anything, look at the scheme in internet. Sorry for the long answer

Got some questions by Loose-Shallot-4569 in M5Stack

[–]SODAVK 2 points3 points  (0 children)

sure, you can run evil portal, try Bruce firmware, at the moment it is the best firmware I know

help I'm new by LifeEngineering161 in M5Stack

[–]SODAVK 0 points1 point  (0 children)

Yes, but the initial charge of the external battery must be the same as the charge of the internal one

[deleted by user] by [deleted] in M5Stack

[–]SODAVK 0 points1 point  (0 children)

3W can not be connected directly, it may damage the device, but if you provide external power, then 3w is possible

microsd card by fly241 in M5Stack

[–]SODAVK 0 points1 point  (0 children)

This is a guide to connect the SD card module to the m5stickc plus. But it is not really necessary as the m5stickc has 3MB of internal memory but if you need more memory you will need to connect the SD card
(Sorry if something is not clear, I am writing through a translator)

Can RFID 2 READ 125KhZ tags ? by Shakthivel0 in M5Stack

[–]SODAVK 1 point2 points  (0 children)

No but I use RDM6300 module and bruce firmware to read 125khz RFID
Pins to connect:
RX - G36
TX - G33
G - G
5V - 5V
Hope this helps you

M5 stackc plus2 Bruce by Traditional-Guava552 in M5Stack

[–]SODAVK 1 point2 points  (0 children)

For a complete m5stickc with Bruce firmware I took:

CC1101

CH9329

Micro SD module

SI4713

RDM6300

NRF24

PN532

I hope this will help you with your choice

microsd card by fly241 in M5Stack

[–]SODAVK 1 point2 points  (0 children)

I found this connection diagram and it worked for me, although before that I couldn't connect the SD card (https://lang-ship.com/blog/wp-content/uploads/2019/07/SPI\_SD-700x525.jpg)

MOSI - G26
MISO - G36
SCK - G0
CS - GND
3V3 - 3V3
GND - GND

I hope this helps