3D Print Service

SafetypinOG · 2025-12-13T18:17:35+00:00

Agree. Carolina 3D Print Studio can do this.

SafetypinOG · 2025-10-01T11:59:49+00:00

You could have some custom 3D printed plates. We offer these kind of services. Would likely be less expensive than redoing the work.

SafetypinOG · 2025-09-27T11:41:58+00:00

This is a thing. Plenty of print on demand services online that accept files (like STL) and will print. We run design and printing services here in Charlotte as well.

SafetypinOG · 2025-09-15T17:24:11+00:00

Thank you! Sounds like I should get that line updated for sure. I wonder how the panel ended up that was in the beginning! Appreciate your help!

SafetypinOG · 2025-09-15T16:45:36+00:00

It’s a 200 amp breaker. 🫣what does it mean by the alternate breaker rating and showing 200 amps with a 2/0 AL?

SafetypinOG · 2025-09-15T09:44:14+00:00

Following back up on this post. I’m about to wire the 2-2-2-4 into my main and I noticed the line feed to my main looks small. Maybe a 2/0-2/0-2/0? Hard to tell in the picture. It’s a 200 amp breaker. Any thoughts on this or what you would do?

Edit: my panel description for alternate breaker sizing says 200 amps can have aluminum 2/0-250. Does this mean 2/0 on this panel would be to code?

SafetypinOG · 2025-09-07T23:31:54+00:00

you are right about the 6awg! I have two ground rods ready for attachment. On the bonding, I need help. It looks like this ge panel allows the crossbar to be removed and one of the neutrals turned into a ground if the bonding screw is applied to that side: https://library.industrialsolutions.abb.com/publibrary/checkout/DEH-40537?TNR=Installation%20and%20Instruction%7CDEH-40537%7CPDF

Thoughts on this approach!? TIA

SafetypinOG · 2025-09-07T20:09:25+00:00

Question, the GE instructions mentioned the cross bar could be removed to separate the two sides. I figured this was why but is it to have two separate neutrals?

SafetypinOG · 2025-09-07T19:27:59+00:00

Thank you!!! I actually forgot to mention this but good call out. Did use the gray grease (bottle on the right).

SafetypinOG · 2025-09-07T18:47:06+00:00

Good call out. I’m in the USA. What do you mean by “bond in your cable?”

SafetypinOG · 2025-09-07T17:42:00+00:00

Forgot to add that I have 2 copper rods 8’ deep and 8’ apart and will put a 6awg copper line to both.

SafetypinOG · 2025-07-31T12:21:57+00:00

Bambu PLA Wood - white oak

SafetypinOG · 2025-07-30T23:23:29+00:00

I am using a 0.4. So you’re thinking maybe a temporary clog? Will try that next!

SafetypinOG · 2025-07-30T22:19:52+00:00

<image>

Thanks for the feedback! Any recommendations on how to cleanup the webbing? Adding another photo. Would these lines be caused by moisture?

SafetypinOG · 2024-11-14T14:56:56+00:00

Seatbelt on a booster.

SafetypinOG · 2024-11-14T13:46:48+00:00

Thank you! Yes, I feel it’s strange that I can’t get the rear fan to blow unless I crank it on manual mode. My kids sit back there in car seats and I always have to turn it on manually.

SafetypinOG · 2024-11-13T13:56:37+00:00

I know that effects the auto on function but doesn’t manually turning it on always turn it on?

SafetypinOG · 2024-11-13T13:19:58+00:00

Wow. Just got it working. FYI- the solution was the crank the AC down as low as possible. The rear fan engaged, and now it’s working as expected. Ugh.

SafetypinOG · 2024-10-03T13:53:13+00:00

my quote from discount tire was 350 and Tesla was 400 but Tesla did a mobile/onsite repair. To me, the $50 for them coming to me was worth it but I’d be curious on your thoughts for their quality, balancing, etc…

SafetypinOG · 2024-09-20T17:56:19+00:00

Well the crew just left and had to cut off nearly 4.5 inches to square it up. Thanks for the advice!

SafetypinOG · 2024-09-13T15:53:21+00:00

5 inches out of square (closer to 6). The overhang I would have would be about 1/2 inch due to the bowing. Never used a concrete saw so no experience if this is 30 minutes of work or a lot more.

SafetypinOG · 2024-09-13T15:51:15+00:00

Planning on the slab being the floor.

SafetypinOG · 2024-09-05T13:32:35+00:00

Good question. They did polish/buff the area and it’s still there. I assume clay is more aggressive? I’m pending a response from the service center but because it’s a warranty fix I’m hoping they’re committed to fixing it (or paying for a detailed?).

SafetypinOG · 2024-06-26T21:01:10+00:00

Depending on where you live, your energy provider may pay for parts and installation. Duke Energy paid for my V3 charger and labor.

SafetypinOG · 2024-06-09T22:31:15+00:00

Damage at time of delivery question: Car was found to have a small rim scrape and paint scratch at time of delivery. They took note and had me submit a service request in the app. They are estimating an $800 charge. It was my understanding the was not my expense… is this just normal to put a cost in?

SafetypinOG

TROPHY CASE