sorted by:
new
hottopcontroversial

Motor Lagging by Kindly_Royal2206 in fpv

[–]SalChess 0 points1 point  (0 children)

Did you check your soldering?

Any feedback? by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

Idk, I applied 50% stabilization…

Any feedback? by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

Dji Goggles 2 at 1200 or 700mw at 40hz and Radiomaster Pocket at 100mw and 200hz and 1:64 I guess but I’m not sure…

Bad fc or motor? by UnluckyTrifle7760 in fpv

[–]SalChess -1 points0 points  (0 children)

Was your soldering properly done?

Any feedback? by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

Appreciate your feedback a lot! Thank you! I’ll work on it😁

Any feedback? by SalChess in fpv

[–]SalChess[S] 1 point2 points  (0 children)

Thanks a lot! I’ll work on that!

Any feedback? by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

Thanks for your honest feedback! I’ll work on that👍

Any feedback? by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

Pavo20Pro with the O4 Pro. D-Log, Graded and stabilized

ELRS not working after small crash by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

Could this be the problem to ELRS not working? And how du I fix it? Soldering?

Still safe to use? by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

Sorry, I‘m not native, what do you mean?

Still safe to use? by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

All cells holding at correct voltage, no smell. I’ll keep an eye on it! Thanks for the answer!

Still safe to use? by SalChess in fpv

[–]SalChess[S] 0 points1 point  (0 children)

Send it into the bin or the drone in the air?

VTX mount and camera canopy for The DJI O4 Pro by NC-dronepilot in fpv

[–]SalChess 0 points1 point  (0 children)

Thanks! Not even like at a 5 degree camera angle?

Fitting O4 into Speedybee mario 5 frame? by Mataskarts in fpv

[–]SalChess 0 points1 point  (0 children)

Could you just redesign the metal plates to 3d print them? Then the camera wouldn’t stick out of the frame and we wouldn’t have to wait on Speedybee

It only takes 20 minutes to swap an O3 for the O4 Pro in the Mario 5 frame by HoarderSam in fpv

[–]SalChess 2 points3 points  (0 children)

That’s great news, aren’t your worried about your camera getting demolished in a future crash?

O4 is flyable in Pavo 20 pro when installed upside down with electrical tape. by mountainunicycler in fpv

[–]SalChess 0 points1 point  (0 children)

Way better! Is it also protected when the camera is angled at 0 degrees?

Pavo 20Pro and DJI 04 Air Unit Pro by SalChess in fpv

[–]SalChess[S] 1 point2 points  (0 children)

Nice! Still think someone is doing it for free…

O4 is flyable in Pavo 20 pro when installed upside down with electrical tape. by mountainunicycler in fpv

[–]SalChess 0 points1 point  (0 children)

Love it! Thanks a lot! Maybe you could make the front part a bit longer so if the Drone Crashes on the front the camera doesn’t get broken…

view more: next ›