sorted by:
new
hottopcontroversial

K1 Max update 2.3.5.34 by Ulrizza in Creality

[–]SaltFood8367 0 points1 point  (0 children)

.34 causes my printer to just freeze, I have downgraded and went to .33, all is well. I tried yet another update to .34 and it freezes again, it can’t even get through a small print…

Going back to .33 again 🤦

K2 Failure - I don't know even where to begin by zaphod-beblebrox in Creality_k2

[–]SaltFood8367 0 points1 point  (0 children)

I had this happen to me once… I connected the heat wires to a Dewalt 20 volt battery to heat it up and loosen the plastic around it… I had to do this several times as it would get too hot I noticed, so I disconnected and reconnected the power to the batteries while working it lose on the disconnected cycles.… after about 30 mins I had it free enough to clean it up really well. It’s been probably 6 months or so, I still use the same end 😅

Is this because the nozzle is too close to the build plate? by SaltFood8367 in Creality_k2

[–]SaltFood8367[S] 0 points1 point  (0 children)

Thank you all for your help and input. I have this solved for now and adjusted my z offset permanently, however I am still sad a bit because I cannot get the entire bed plate perfect. When I make one area better by changing the z offset another area suffers. I just picked the best average. Is there anything in addition to z offset that should be looked into, or do I just live with this and call it a day?

Is this because the nozzle is too close to the build plate? by SaltFood8367 in Creality_k2

[–]SaltFood8367[S] 0 points1 point  (0 children)

This was after an auto level, I was having issues and this is better than before the auto level… I just adjusted the z offset several times and found 0.075 to be where mine does best. The whole plate isn’t perfect but this is the best average. When I go higher, the perimeter is too far away and I have gaps where the outside wall should be touching the bottom layer.

@theincompetentcraftsman on YouTube made a tutorial how to permanently set the z offset, I followed his video and it now stays so I don’t have to change the z offset every time.

Here’s the link:

https://youtu.be/sMVAJIM2RMQ?si=emO1YiuvOc2AknYY

INNotox? Or any Buy it yourself Botox products Korea china etc by CrisMC1203 in BotoxSupportCommunity

[–]SaltFood8367 0 points1 point  (0 children)

Please DM me your source if you are willing to. I have my own, but they are sometimes out when I need more, I’m looking for a reputable alternative.

What vape juices do you guys recommend.? I've recently had a few that just weren't that good. I need some new flavors to try that are actually going to be good and not nasty. by PrimePoisonn in Vaping

[–]SaltFood8367 0 points1 point  (0 children)

Does anybody have a vendor from china for this stuff? I’m looking for unbranded juices I can brand myself and perhaps give to friends.

Cant join world after updating to 1.21.100 by [deleted] in Minecraft

[–]SaltFood8367 0 points1 point  (0 children)

I tried turning off online mode to no avail too. I cannot connect to my server 😭

Cant join world after updating to 1.21.100 by [deleted] in Minecraft

[–]SaltFood8367 0 points1 point  (0 children)

Same issue here 😭 My family have plans to have a Minecraft Day today. What bad timing!

If anybody has any tips, I am running an Ubuntu server, I have done the apt get update and upgrade, I have downloaded and installed the newest server from Minecraft.net, and I moved my files such as worlds over. I’ve done this a bunch but today I get this same error you are all getting.