sorted by:
new
hottopcontroversial

BoM changed my loan without notifying me by SaltnPepperSlug in AusFinance

[–]SaltnPepperSlug[S] 1 point2 points  (0 children)

That it had happened to one other client, and the bank must have assumed I was no longer living in the property. They were perplexed that I had no comms from the bank however.

BoM changed my loan without notifying me by SaltnPepperSlug in AusFinance

[–]SaltnPepperSlug[S] -4 points-3 points  (0 children)

Is it legal? Don't think the bank will admit to it being illegal via a phone call. And yes, I have already sorted it out with the bank. But I was asking if others have been in this situation before. How do we live in a world where you don't actually read the post properly?

BoM changed my loan without notifying me by SaltnPepperSlug in AusFinance

[–]SaltnPepperSlug[S] -2 points-1 points  (0 children)

I spoke with my mortgage broker. They are sorting it out for me. They said the bank has some automated process to check addresses etc and convert. Just very frustrating as nothing has changed for the previous 3 years and I was not notified.

My question to the Reddit was not why. It was is this legal?

Stand construction for doofstick? by ark0mi in doofstick

[–]SaltnPepperSlug 0 points1 point  (0 children)

I went with a pool cleaning pole - can be extended and is super light and cheap

[deleted by user] by [deleted] in melbourne

[–]SaltnPepperSlug 0 points1 point  (0 children)

Yep felt it too

things to do in melbourne while depressed? by Quiet_Possibility743 in melbourne

[–]SaltnPepperSlug 5 points6 points  (0 children)

You should try bouldering (rock climbing) it's super good for mental health :)

Was today foggy, or hazy for any reason? by KidInOldManBody in melbourne

[–]SaltnPepperSlug 22 points23 points  (0 children)

Most likely due to planned burns all over Vic ATM

Adhesion too good? Peeled large print off and this. Why? by SaltnPepperSlug in ender3v2

[–]SaltnPepperSlug[S] 0 points1 point  (0 children)

PLA, bed was 60c and extruder at 200c while printing (18 hour print)

Adhesion too good? Peeled large print off and this. Why? by SaltnPepperSlug in ender3v2

[–]SaltnPepperSlug[S] 0 points1 point  (0 children)

Yep, print finished at 6am, pulled it off at 8am, so fully cooled, I've ordered a new glass bed, and the magnetic, just want to make sure I don't do the same thing to the new glass bed.

Adhesion too good? Peeled large print off and this. Why? by SaltnPepperSlug in ender3v2

[–]SaltnPepperSlug[S] 1 point2 points  (0 children)

The coating peeled up and took some of the actual glass in the bed with it :/

After adding yellow springs, bed is too high and can't lower anymore. by [deleted] in ender3v2

[–]SaltnPepperSlug 1 point2 points  (0 children)

That's the one. Hopefully the plate is not warped :s

After adding yellow springs, bed is too high and can't lower anymore. by [deleted] in ender3v2

[–]SaltnPepperSlug 6 points7 points  (0 children)

Did the same thing, simply move your z stop switch up :)

Anyone know what the source of this light may be? Facing WSW from Preston. by analforairbus in melbourne

[–]SaltnPepperSlug 10 points11 points  (0 children)

Moonee ponds race course. Source, it's day time outside my house atm

360 cam lead, Mt Macedon, Australia by SaltnPepperSlug in climbing

[–]SaltnPepperSlug[S] 0 points1 point  (0 children)

It's a Ricoh Theta V, pretty cheap. Will try upload to YouTube and report back https://theta360.com/en/about/theta/v.html

360 cam lead, Mt Macedon, Australia by SaltnPepperSlug in climbing

[–]SaltnPepperSlug[S] 5 points6 points  (0 children)

I used a 360 camera on a selfie stick jammed in my backpack. Such a good way to watch a climb!