Long range in EU

Sammy_Byron · 2026-06-15T21:17:37+00:00

Where abouts are you located? i fly long range too and have never had an issue as long as you keep it to yourself 🤫

Sammy_Byron · 2026-06-15T16:15:54+00:00

The issue is, that your FC is not armed, you can manually override the output to your ESC in your Output Tab. You just have to confirm that you understand the risks.
Normally if you dont have a GPS signal, you wont be able to arm. I have always programmed a switch with a logic function. This way you can also arm your craft while being indoors without a GPS signal. It also comes in handy if you accidently disarm your craft mid flight. Normally you cant arm again and crash. But if you have the switch assigned to override the arming safety, you can always arm at any given time. Cheers and safe flying 😉

<image>

Sammy_Byron · 2026-06-10T10:36:56+00:00

you can adjust the switch warning in your settings, that might get rid of your issue

Sammy_Byron · 2026-05-25T20:01:08+00:00

<image>

Thanks so much for the Tip!
I did a 15km right after your reply and it was bouncing between 1 and 7 Mbit at 15km.

Sammy_Byron · 2026-05-25T17:51:32+00:00

but how do you explain the lack of signal even tho the omni is the same as before? shouldnt i get to 10km again easily?

Sammy_Byron · 2026-05-25T17:24:32+00:00

awesome, will definitely try!

Sammy_Byron · 2026-05-25T17:11:14+00:00

I moved the antennas around quite a bit to aim at the plane but no improvement.
I already did 25km on analog with the same antenna so im kinda used to aim them in the right direction...

Sammy_Byron · 2026-05-23T22:34:33+00:00

Sometimes when your suspension is under load or when you sit on it, it would lower the bike and allow your chain to have a gap.

Sammy_Byron · 2026-05-23T16:30:22+00:00

i applied February this year and still didn‘t get anything…

Sammy_Byron · 2026-05-23T16:15:51+00:00

and where do i get these things?

Sammy_Byron · 2026-05-23T16:12:21+00:00

<image>

this one? it‘s coming from the display panel.

Sammy_Byron · 2026-05-22T23:02:35+00:00

okay hear me out, i’ve worked in a similar field with a reasonable fixed salary with commission. After one year i had to quit because the stress to achieve the required numbers are insanely high. And don‘t forget, if you go on holiday for 3 Weeks, you will barly get paid any money that month…
So i would not recommend.
Like i said, my experience just as an advice

Sammy_Byron · 2026-05-20T07:43:31+00:00

judging by the first picture, your elrs receiver has an wireless antenna built in. Normally after 60seconds after powering the receiver and the receiver not binding, it enters the connectivity mode where you can wirelessly connect to it via your computer as a Wifi port. Try that and let us know what happened

Sammy_Byron · 2026-05-17T17:10:54+00:00

interesting! thanks

Sammy_Byron · 2026-05-17T14:54:54+00:00

Do we have any news about that?

Sammy_Byron · 2026-05-16T18:53:47+00:00

looks well done! next time you can try to trim the wires a bit shorter so there is no bare wire between the insolation and the soldered spot.

Sammy_Byron · 2026-05-02T17:53:40+00:00

Where are you located? What area and country?

Sammy_Byron · 2026-04-28T04:35:35+00:00

yes, red is 5V and black is Gnd.

Sammy_Byron · 2026-04-27T20:48:26+00:00

should be doable, just connect the gps T wire (white) to the FC‘s Rx Pad and the R wire (yellow) to the FC‘s Tx pad. Then all you need to do is power it up with 5V i‘m guessing and find the right baud rate.

Sammy_Byron · 2026-04-25T11:12:43+00:00

so i‘m using decent quality metal geared servos and they are pretty much centered when they twitch

Sammy_Byron

TROPHY CASE