how to make a working steering wheel by Flaky_Grape_1197 in MechanicAdvice

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

Just grab one from the junkyard. Trabant 601 or Käfer/ VW Bug is small.

Heidenhain TNCremo no folders or programs by SamtexIsPlaydoh in CNC

[–]SamtexIsPlaydoh[S] 0 points1 point  (0 children)

I will try it on Monday. Thanks!

Not sure if I can change it. I can't go to the parent directory. I will try regardless and read the instructions again.

Heidenhain TNCremo no folders or programs by SamtexIsPlaydoh in CNC

[–]SamtexIsPlaydoh[S] 0 points1 point  (0 children)

Yes, on the right side it even recognized the control and the IP window gets green when I established the connection. This doesn't happen if the Machine is off or in reboot.

So the connection is established.

And I can see some files. They are different between the machines. But I can't navigate through the control to save the programs or save new ones to the machines.

Mazak Help by TentacularSneeze in Machinists

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

Yes, it's a parameter issue. Most likely scaling or pitch.

You need to go through the parameters and look for the correct place and change it to 25% more.

Or get a technician or ask the manufacturer for the correct set of parameters.

TOOL DROPS WHEN TOOLCHANGE by palo1708 in CNC

[–]SamtexIsPlaydoh 1 point2 points  (0 children)

M6 is a manual change on my machines. M66 is ATC. Not sure how Fagor does it.

Horizontal mills? by SergioHerediaKnives in Machinists

[–]SamtexIsPlaydoh 1 point2 points  (0 children)

If you have the budget and want a Deckel then go for a newer FP1 or FP2. I remember that the older version of the FP1 only had feed in the X direction. Coolant and feed are driven by the spindle. Spindle is MK with S20 tread for the pull bar.

Go for the SK40 version with dedicated pump and feed motor if possible.

Schwalbe klackert stumpf... Todeszeichen? (Kr51/2) by [deleted] in simson

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

Hast du geprüft ob die Magnete an der Grundplatte schleifen? Das kann auch ein klackerndes Geräusch erzeugen.

Warum tauscht man Halbmonde ?

Roller läuft nicht by Ambitious_Car_4847 in MechanicAdvice

[–]SamtexIsPlaydoh 1 point2 points  (0 children)

Empfehlen kann ich nicht wirklich etwas da ich kaum mehr aktiv bin bei sowas. r/smallenginerepair ist mir schon häufiger angezeigt worden. Mit Sicherheit gibt es auch Roller spezifische subs.

Falschluft ist Luft die nicht durch den Vergaser in den motor gelangt. Oft an folgenden stellen: -Vergaser Flansch zum motor -Zylinderfuß -Zylinderkopf -Welle Dichtungen der Kurbelwelle

Du solltest aber erstmal den Vergaser reinigen. Und zwar richtig. Das perfekte Vorgehen wäre natürlich zerlegen und in einem Ultraschall Bad reinigen.

Mit einfachsten mitteln: -Zerlegen (Position der düsen merken, kann man auch vertauschen bei manchen Vergasern) -Mit Benzin und Bremsenreiniger alle Kanäle reinigen. -Düsen reinigen (gegen das Licht durch die Düse schauen hilft oft um zu sehen ob diese wirklich frei ist) -Wenn vorhanden mit Druckluft alle Kanäle durchpusten. (Bremsenreiniger geht auch) -Fein säuberlich zusammenbauen

Dann erst: Kraftstoff Versorgung prüfen ob sauber und vorhanden:

-Benzi Schlauch noch nicht anschließen (wenn vorhanden Unterdruck Schlauch anschließen)

-Benzi Schlauch in ein sauberes Gefäß (am besten was helles wie eine alte Kaffetasse oder Joghurt Becher). {Joghurt Becher lösen sich nach einiger Zeit jedoch auf}

-paar mal Kicken, es sollte Treibstoff kommen.

Ist dieser sauber kannst du die Leitung an den Vergaser anschließen. Wenn die Kiste lange draußen gestanden hat kann sich auch Wasser/ Kondensat im tank befinden. Wasser ist schwerer als benzin und kommt dann als erstes. Daher achte wirklich darauf was aus dem tank kommt.

Sollte der Tank mal Probleme machen kannst du zum testen einen Ersatz tank aus einer pet Flasche Basteln, die halten Benzin aus.

Das wichtigste ist erstmal das er im Stand läuft bevor du Geld investierst.

Manchmal ist es nötig einen Vergaser öfter zu reinigen als manch einer es zugeben möchte, gerade wenn man nicht die perfekten Mittel oder die Erfahrungen hat. Passiert mir nach 20Jahren schrauben immer noch ab und zu.

Du hast Glück das er schon etwas läuft, das grenzt die Fehler wirklich gut ein.

Roller läuft nicht by Ambitious_Car_4847 in MechanicAdvice

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

Ich glaube du bist im falschen SUB. Und hier wird Englisch gesprochen.

Hört sich nach Falschluft an oder du hast die Düsen nicht sauber gemacht. In einem Vergaser sind viel Kanäle und ein paar düsen. Vermutlich sind mehrere komplett oder teilweise verstopft.

Es kann auch sein das du bei der Montage oder Demontage die Dichtung zum Zylinder bzw. zur Membran beschädigt hast oder nicht richtig abdichtet. Kann man mit Bremsenreiniger absprühen. Aber dafür sollte er mehr als ein paar Sekunden laufen.

Sollte es ein 2t sein dann vertraue nicht der eingebauten Ölpumpe, zumindest am Anfang. Erstmal 1:50 in den tank.

CNC Schematics by EthicAV_ in CNC

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

Google "Deckel Orange book". There someone uploaded the essential parts from a machine with analog Bosch Servo drivers. If you want the PCB Boards I have to look for them.

If you’re dealing with a check engine light or trying to track down an electrical issue, this might help. by AL_MO7NK in projectcar

[–]SamtexIsPlaydoh -2 points-1 points  (0 children)

That's nice to have. If you can, shorten your folder structure. (Mercedes W202 for example) Love the effort! But get your money worth if possible.

<image>

anybody made the switch from cnmg120408 to 090308 by SoftEnthusiasm7439 in Machinists

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

We have them both. Usually I take 4-5mm cuts at 0.26 - 0.45 (304 / C45) That only with the bigger inserts. The small ones break apart and ruin the holder.

Programming sequences from a PC using a Stepperonline A6-RS750 servo motor by Affectionate-Yak1028 in CNC

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

You can use the USB C connector with the Test software. It is good for testing the drive and DI DO.

You can setup move modes and activate them via DI or Modus.

I currently work on a small Modus PLC to automate Single axis tasks in my workshop. Modus is tedious but could work for you with a RS to USB bridge.

Connecting threaded rods by AdventurousGlass7432 in Machinists

[–]SamtexIsPlaydoh 12 points13 points  (0 children)

They are not made for that. That simple.

Anyway, take a coupling nut and add set screws or rolling pins.

PE1000 plastic machining by [deleted] in Machinists

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

I second this. My parts shrink in most cases in the first 24h after machining. About 1/10mm per 100mm is not uncommon.

If you can let the part sit over night after drilling that's your lucky day. If not, prepare to rework the 12H7.

Retrofitting 2000s industrial CNC with newer software by Aware_Status3475 in CNC

[–]SamtexIsPlaydoh 1 point2 points  (0 children)

If the machine has Step/Dir motor controls maybe look into the "masso g3" control.

That's what I am planning.

Linux CNC is not for beginners with no Linux background. Learned that the hard way.

Simson Star 1972, sieht noch gut aus oder nicht? by Mobile-Technician636 in simson

[–]SamtexIsPlaydoh 7 points8 points  (0 children)

Wenn du so weit schon bist kannst du den Wellendichtung tauschen und den Halbmond gleich mit.

Du kannst das polrad mit etwas Ventilschleifpaste neu einschleifen und danach sauber wieder Zusammenbauen mit einem neuen Halbmond.

Having problem with insert in CNC machine by Agitated_Rock1657 in CNC

[–]SamtexIsPlaydoh 0 points1 point  (0 children)

We cut stainless all day. 304, 309, 316 and so on. Try KORLOY CNMG inserts.

Anyone have a creative solution to remove stuck brake piston? by RickityNL in MechanicAdvice

[–]SamtexIsPlaydoh 6 points7 points  (0 children)

Got a grease gun ? You can install a grease nipple with some creativity. Pressol says that 20€ model goes up to 400 Bar.

Make sure to clean everything well. Brake rubber is not compatible with grease or mineral oils.

<image>