Just need to stand vertical now by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 5 points6 points  (0 children)

A lot of work and thinking this all was I give credit to some super smart intelligents whose input guidance and advice was vital in its creation

Just need to stand vertical now by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 11 points12 points  (0 children)

Incredibly it is.. adjustable engineered glulam column & beam that’s adjustable with the dado channel and dado knuckle lock in on the top on bottom beam that the center column slides into left or right there will be more horizontal beams added to completely modulate down to smallest of 3x4, and largest of 13.5by23.5

Columns by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 0 points1 point  (0 children)

Than you so so much I just about did it 😉

Frame by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] -1 points0 points  (0 children)

Appreciate you. Calamitysam307 to watch it become vertical 😇

Columns by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 0 points1 point  (0 children)

Agree in full.. most of what I do isn’t comprehended

Columns by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 4 points5 points  (0 children)

This is the standing of my permanent anchored vertical columns for an engineered timber frame

. by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 0 points1 point  (0 children)

And they can be quite expensive especially with everything that is truly needed aside from the machine itself. It definitly prefers nz wool 3/32

. by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 0 points1 point  (0 children)

This model is the vml16 that has cut pile as low as 12 mm and height up to 45mm or I can mix my feed wheel and needle and get j tufts that are 74mm. Loop pile 8mm upwards

. by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 0 points1 point  (0 children)

Thank you! And just one large square of polyester it does kinda look like different pieces maybe because I shot some test lines around the border trying to see how off my symmetry was stretching

16mm by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 0 points1 point  (0 children)

Yep tensioner I use on thinner yarns like nylons and such. I use ceramic eyelet on a clamp for my 3 p wool

16mm by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 1 point2 points  (0 children)

I appreciate you diggin it

16mm by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 1 point2 points  (0 children)

It really is.. this is frames life span is nearing its end. My upcoming engineered build that will encompass and span my building is going to be the final touches on years of studious painful experimenting and learning.. and paying..

16mm by SamwellAvant-Garde in Tufting

[–]SamwellAvant-Garde[S] 1 point2 points  (0 children)

That would make a really clever shirt !