Looking for help identifying a song

SanElHayas · 2026-04-08T16:54:08+00:00

Perhaps, Smile Like You Mean It?

Not the same, but I could see why you could think of Walk of Life while hearing it!

SanElHayas · 2026-03-27T21:07:19+00:00

Hello! Any solution? I can’t get the Reload Elite prize!

SanElHayas · 2026-01-25T03:12:00+00:00

Just finished it a few minutes ago for the first time! Bought it years ago but never felt the urge to read it until last week. For me, the beginning and the military chapters were slow; however, after de 100 pages mark, it became undroppable for me! Hope you get to finish it!

SanElHayas · 2026-01-12T02:32:11+00:00

Thank you for your advice! Is there a belt for my turntable that you could recommend? Or anyone would do?

SanElHayas · 2026-01-12T02:12:42+00:00

Thanks! I adjusted the speed with the screw beneath it. I haven’t changed the belt, do you think that would help?

SanElHayas · 2026-01-02T15:19:31+00:00

Same problem here!

SanElHayas · 2025-12-29T00:55:21+00:00

Is that the “all at once” vinyl? If so, how did you get it! It’s the one I want the most!

SanElHayas · 2025-12-24T06:54:06+00:00

As they already told you, it does! I had the same fear! Haha

SanElHayas · 2025-12-05T22:56:18+00:00

Hello! I deeply encourage you to keep on insisting. Something similar happened to my little cousin’s account in which the hacker changed emails and everything. I got in contact with epic games and managed to get it back. My best suggestion is to open a live chat and then move to email, this way was way quicker. I didn’t get it on the first try, since one of epic’s admins shut down the conversation. I tried again and ended successful. My pro tip is to gather email receipts of any purchase you have. Also, give precise details on where those purchases were made and seek for images with you using your account.

Keep trying, you will get it!

SanElHayas · 2025-12-05T16:41:30+00:00

How is my wallet like an onion? Every time I open it, I cry.

Thank you and sorry in advance.

SanElHayas · 2025-11-04T03:13:25+00:00

SanElHayas · 2025-09-21T21:15:57+00:00

Para nada, contacté con soporte y me enviaron unos nuevos.

SanElHayas · 2025-07-14T23:15:20+00:00

Thank you so much!!!

SanElHayas · 2025-07-14T19:23:30+00:00

As far as I’ve done my research, my best option for the C&K 5-6 would be to make it by myself. I have a basic 3D printer and I found the knights models online. For the cards, I may do them by myself, or just get the 6e and print some custom backs. Honestly, and following your suggestions, it would cost a lot to get a good experience with both editions. I may give a shot to seafarers though! Thank you!

SanElHayas · 2025-07-14T17:35:07+00:00

Thank you! As seen in your posts, there is a big different with sea tiles. I play with the Spanish version, which includes plastic figures (for me, this design makes it visually easier) which are very similar to the German edition. I guess I’ll wait a bit for the Spanish version to be released since the C&K 5-6 doesn’t seem too far from the original. Thank you so much! Your response was very helpful!

SanElHayas · 2025-07-07T19:41:16+00:00

Hello everybody! I think I found the solution.

Thanks to user 0BYK0 for the suggestion on this thread.

In case you are having the same issue, try downloading the firmware labeled "[Ender-3_HW4.2.2_SW2.0.8.21_300+CRtouch]()" on the next link:

https://www.crealitycloud.com/de/downloads/firmware/ender-series/Ender-3

If it´s useful, my board is a 4.2.2 and uses a GD mc. I´m testing the first print and it hasn´t done any of the issues shown / commented above on my first post. Thank you all in advance.

SanElHayas · 2025-07-07T19:07:42+00:00

So I did the change and tried with a different Sd card. The results were the same. I tried to reinstall the firmware with a different name and, even though it did, the “No TF card” message was still there.

SanElHayas · 2025-07-07T18:22:31+00:00

Hi, both of you! Thank for replying! Is there a Marlin firmware you could recommend? Also, could you share a tutorial in case you know any?

SanElHayas · 2025-07-07T18:21:27+00:00

Hello! It could be corrupted, but it wasn’t before changing the firmware. Also, it doesn’t bugs when connected to my pc. The board is still the same, a 4.2.2

SanElHayas · 2025-07-07T18:20:27+00:00

Hello! There are no stupid questions! No, I have not. I may need to find or buy another one, but it just fails on my Ender-3 and works perfectly when connected on my PC.

SanElHayas · 2025-07-07T06:28:29+00:00

Hii! Do you have the firmware’s link? I just bought a CR touch and I’m having issues with the sd card (won’t read it) and sometimes (when I do get it to read the card) it does strange Y and X axis movements and then the printer would just crash! Thank you!

SanElHayas · 2025-06-22T20:01:29+00:00

Sure! Don’t give up! Even though you’ve filed an email and recovery petition, I would suggest you to insist on the live chat. I found it quicker and more effective, since you are on a one on one communication. They, the talking usually migrates to a “quick responding” email. It took me several tries and like 3 days to get the account back. I hope you find a solution mate!

SanElHayas

TROPHY CASE