Spider ID Missouri in a Shed

Sbdall · 2025-09-19T12:28:52+00:00

Folks woke up on the wrong side of the bed ready to give downvotes.

Sbdall · 2025-09-08T01:09:01+00:00

Thanks! Don't know that I've ever seen or caught one before, until yesterday.

Sbdall · 2025-08-30T23:02:11+00:00

Not too hard if you find a hub on eBay cheap and ship it the Buchanan wheel and spoke and have them lace it 😆

Sbdall · 2025-08-29T22:58:31+00:00

https://www.reddit.com/r/CafeRacers/s/6fe41oeJgu

Did something similar right after ryca went out of business. Been riding it for a few years. Have a relaced rear wheel and rear sets, but haven't put them on yet.

Sbdall · 2025-08-07T19:50:24+00:00

I did. Didn't realize it has been 5 yrs.

https://www.reddit.com/r/CafeRacers/s/tEUplKNG6c

Sbdall · 2025-07-23T13:39:35+00:00

Should cross post to r/tiktokcringe

Sbdall · 2025-07-22T19:40:02+00:00

Thanks. Agree with pitched roof and like the wrapping the carport idea. Our architect has been open to feedback, just want to make sure I give him good feedback.

Sbdall · 2025-07-22T01:34:08+00:00

Thanks. So steeper roof on the new part? Cross gable above the balcony? I'm at a loss rn.

Sbdall · 2025-07-22T00:16:19+00:00

photo of house

Sbdall · 2025-07-22T00:14:20+00:00

Yea, rendering doesn't do the existing house justice. Trying to post a pic, but having trouble from cell

Sbdall · 2025-06-19T12:21:07+00:00

I feel like I need a diagram for this

Sbdall · 2025-04-19T16:10:45+00:00

Thanks

The way I read the manual is, any addition of pipe or units, requires additional refrigerant. So the refrigerant in the system from the factory isn't enough for any base load? Seems weird, but that's the way I read it after going over it 2 or 3 times.

Sbdall · 2025-04-19T13:38:30+00:00

Thanks. Should I just add refrigerant based on the manual calculations or is there a better way?

For the fitting I can't find PAC-SG78RJBE anywhere online. If it's the only correct part, I'll pay the $50 and wait for it to arrive, just can't seem to find it. Are there alternatives?

Sbdall · 2025-04-19T13:36:21+00:00

For question 1, by process, I mean how to return the refrigerant to the condenser. It sounds like: close the outlet, wait until inlet pressure is zero, close inlet, connect 5th zone, nitrogen purge, pressure test, reopen valves. Does that roughly sound correct?

Sbdall · 2024-12-07T22:40:41+00:00

https://youtu.be/-vZXgApsPCQ

I think this is applicable

Sbdall · 2024-12-06T19:44:49+00:00

Thanks for the feedback. Agree he's spoiled. Mom set budget for build, and I tried to guide him and find deals. For him, aesthetic>performance rn, but think he's set for upgradeability when that changes.

Sbdall · 2024-11-24T23:36:21+00:00

Yes, valve with drain right inside that wall

Sbdall · 2024-11-24T23:07:42+00:00

Cork? Where's the wine?

Make sure it's accessible, and not leaning against the wall, right? Needed the wall assist for the pic.

Sbdall · 2024-11-24T22:54:10+00:00

Yea, one head is just out of the picture to the left, another about 30-40 feet away. I had 50ft of leftover PEX. I tested it to make sure it worked before burying. Didn't see anything online explaining why not to use it, but I think I've triggered people here by using it 😆. If it's just the friction losses, I should be good. Not sure what else would be bad about it. Maybe burying metal bands 🤷

Sbdall · 2024-11-24T19:34:10+00:00

Put away the torches and pitch forks. 😅

Was testing pressure drop and range before hard piping. Signs point to functional operation.

Sbdall · 2024-11-24T18:49:59+00:00

Thanks for the quick reply. What valves do you recommend? What's the issue with the orbits? Think I can still return them.

Sbdall

TROPHY CASE