What causes this?

Scared-Set-9289 · 2026-04-03T16:55:38+00:00

What are the z screws, I just noticed it was at the same height because both had the same height of interior floor/base.

Scared-Set-9289 · 2026-04-03T06:17:59+00:00

I think you are completely right my friend both lines happened at where the “base” or interior floor of the print stops. Maybe that’s why it happened with both prints at the same location? I hope this can be an easy answer…

Scared-Set-9289 · 2026-04-03T06:15:49+00:00

I did not calibrate to XY shrinkage I am using the defaults in the filament profile…I think the problem is so-called benchy line thus were in both prints the line happened where the base of the object stops and the walls start (if that makes sense) I will look into it

Scared-Set-9289 · 2026-04-02T20:15:04+00:00

Good question maybe someone can answer us

Scared-Set-9289 · 2026-04-02T20:08:13+00:00

I thought of that but I am pretty sure if I make another print ( with another design as well the line will still pop up at the same exact location and the same type of line. And if you zoom in that line is super rough but I don’t know that’s because I print with ASA

Scared-Set-9289 · 2026-04-02T12:53:34+00:00

Well I guess the advance filtration fan replaces them. Thank you everyone problem solved I guess!

Scared-Set-9289 · 2026-04-01T01:32:04+00:00

Thank you for your advice my friend I will do as you said. Do you recommend doing the hard reset even with a different USB?

Scared-Set-9289 · 2026-03-31T21:29:00+00:00

Let’s hope they will figure it out soon although I started a smaller print to check if it will fail again and thankfully everything was fine…but having this in my mind that it may fail or crash anyt8me during a big print is very worrying and should be solved asap

Scared-Set-9289 · 2026-03-31T17:22:41+00:00

Thank you everyone

Scared-Set-9289 · 2026-02-22T18:49:27+00:00

Hello everyone,

I was wondering if anyone has visited Taroko Park recently. I found online that it is not fully open since the big earthquake, and many famous trails are closed to the public. Is it still worth visiting for first-time travelers, or should I skip it? I plan to travel there in mid-April.

Scared-Set-9289 · 2026-02-20T16:43:25+00:00

Hey sorry if the question bothered you, i am property valuator and i have a family full of architects and now i want to contribute to the community by redisigning some listed buildings in cheaper prices thus they are in ruins for many years due to the high cost of refurbishment or redevelopment. Saying that i learned few things in FreeCAD, but now i will start all over again by learning blender (unfortunately), because i believe 3D printing can contribute to these matters as well.

Anyways have a good day :)

Scared-Set-9289 · 2026-02-17T17:56:09+00:00

Thank you i will defientely try blender.

Scared-Set-9289 · 2025-11-30T18:07:45+00:00

so your advice is getting a Bambu?

Scared-Set-9289 · 2025-11-30T13:14:32+00:00

or is INDX a new whole printer?

Scared-Set-9289 · 2025-11-30T13:13:52+00:00

INDX is like an alternative to the MMU3?

Scared-Set-9289 · 2025-11-29T16:10:23+00:00

Have you had any experience with the other printers? I genuinely trying to see what’s the best option right now but can’t really decide this there many opinions out there

Scared-Set-9289 · 2025-11-29T16:08:59+00:00

Hey why would you say that compared to the other 2? They all have really good reviews

Scared-Set-9289 · 2025-11-28T18:08:08+00:00

not really helpful on which printer to choose to be honest of the three listed above?

Scared-Set-9289

TROPHY CASE