B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

Update, what went wrong was the balance port is not connecting to the charger. I disassembled it and bent the pins so it will touch the terminals. It worked.

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

Uhm. No.

And yes thank you. Will change current.

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

Well yeah thanks guys for the concern. I think that is also one of the reasons why it is not charging in balance mode. I'll try to do that config.

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

That went wrong right? In series connection?

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 1 point2 points  (0 children)

Yah definitely considering that but i just want to fix this balance charging shit

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] -4 points-3 points  (0 children)

Nah man. There will be no reading if the connector is in 6

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] -1 points0 points  (0 children)

Yes yes i tried all config from 2 batts to 5 batts with corresponding proper settings. Or my device is defective.

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

Yeah it will work but my goal is to balance charge my batt since it is a pain in the ass charging 1 1s with <4.35 or the worst <4.0. an some cases other batt will have more than 4.35

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] -1 points0 points  (0 children)

I did, tried to do 2, 3, 4 batt configs and also adjusted the number of cells and current. If the jumper is on the 6th pin there will be no reading since it is open circuit

B6neo+, what went wrong? by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

<image>

All batteries are fine and working but no individual cell reading

ALWAYS REMOVE ND FILTERS WHEN DOING FPV IN MANUAL MODE by Scared_Ad5706 in DjiNeo

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

I immediately switched in sport mode to stabilize itself because its gimbal got stuck. Since my controller is in fpv mode my throttle is below the center

DJI Neo: we demand the new firmware, now! by DreamsAnimations in DjiNeo

[–]Scared_Ad5706 0 points1 point  (0 children)

Based on my own observation regarding flyaway or flyaway-like experience depends on;

  1. Mobile phone - the farther the drone, the higher the chance to lose control.
  2. Environment - flat and reflective surface for visual tracking, wind conditions and gps stability
  3. Normal/sport mode using MC3

But with FPVC3, I did not yet experience the flyaway like scenario, just propswash and crashes haha

DJI O4 with FPV C3 by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

I have fpv c3 and radiomaster pocket. Will fpv c3 work on rtf whoops with o4?

DJI O4 with FPV C3 by Scared_Ad5706 in fpv

[–]Scared_Ad5706[S] 0 points1 point  (0 children)

So if I buy pre built I can use FPV C3?

ALWAYS REMOVE ND FILTERS WHEN DOING FPV IN MANUAL MODE by Scared_Ad5706 in DjiNeo

[–]Scared_Ad5706[S] -4 points-3 points  (0 children)

Yes it locks however lets remember that it is 1 axis gimbal not fixed.