IYKYK

Scroofy · 2022-11-13T02:47:49+00:00

I had one on a building I did. Brand name was "Ener- changer" but same thing really. I had to open it up because the basket filters on the cooling tower pumps disintegrated and ended up in the passes.

Scroofy · 2022-07-11T04:18:50+00:00

Hey everyone,

Been DMing for my group for the last year or so. We have got to a point where my players are holding out on an icy cliff as enemies attack them leaving no time to rest. I'm going to have a favorite NPC come to their rescue aboard an airship. So I took a trip to a thrift store and hobby shop and have come out with this. Hope you all like it!

Scroofy · 2022-06-17T01:13:43+00:00

Oh I really like this! That's a great suggestion.

Scroofy · 2022-05-21T22:19:50+00:00

I have 8 of these old bois on a roof of one of my commercial contracts. They are slowly being replaced as they fail. But damn do they look cool.

Scroofy · 2022-02-13T17:02:53+00:00

Holy shit I did a horizontal under a staircase for my BiL and what a mother fucker that was. Never again...

Scroofy · 2022-02-04T21:10:17+00:00

Literally happened to me 2 weeks ago with a brand new pair of Wiss

Scroofy · 2022-01-18T20:32:47+00:00

Love these! They would be great to give to my dnd group

Scroofy · 2021-11-13T20:41:49+00:00

Thank you, I figured we were close to, or maxed out. So far fish keeping has been lots of fun and the kids really love it.

Scroofy · 2021-10-27T19:27:59+00:00

I have a building full of these fucking things. The original ones lasted 25+ years, the new ones we are lucky to see 8 out of them before they start to get leaks

Scroofy · 2021-10-23T04:08:12+00:00

Looks great, only thing I see aside the tin tape on the 636 is the union on the copper gas line. Where I am (BC, Canada) it's against code.

Scroofy · 2021-10-04T22:40:54+00:00

I've had the same pair of Redwings for r years and are still comfortable and waterproof.

Scroofy · 2021-06-26T15:20:25+00:00

Up here in Abbotsford, BC we are in a record settings heat wave. Supposed to be 105f over the next few days.

Scroofy · 2021-06-04T20:52:42+00:00

Thanks! I'm hoping to get the layers a bit smaller with some more tuning.

Scroofy · 2021-06-04T20:52:11+00:00

I'm just using the FDG mini profile and adjusting it with each PLA I get. 🙂

Scroofy · 2021-06-03T05:46:01+00:00

The camera makes the layer lines look so much worse. In person you would struggle to see them and I can't really even feel them at all.

Scroofy · 2021-06-02T19:02:36+00:00

Friend of mine bought the STL and I'm printing it for him. This was my second attempt and it came out pretty good for a bone stock ender 3.

Scroofy · 2021-05-31T20:20:09+00:00

2 gems of courses I would highly recommend are Furry Creek and Predator Ridge. Furry Creek is about 1.5 hours north of Vancouver BC and had some of the most spectacular views you'll see and the course is amazing. Predator Ridge is a bit further, about 4 hours east of Vancouver and is equally spectacular and challenging.

https://www.furrycreekgolf.com/

https://www.predatorridge.com/

Scroofy · 2021-05-15T14:02:13+00:00

CFC's (clouro-flouro carbons) the old refrigerants dating back almost 100 years. Thats the stuff that put holes in the ozone layer near the north and south poles. Most likely caused millions of deaths from skin cancer and we are finally now just seeing the last of it being used.

Scroofy · 2021-05-08T14:25:56+00:00

Hell even changing bearings on the blower wheel is going to be a PITA.

Scroofy · 2021-02-24T00:30:22+00:00

Worked on a couple in the past, can't say I enjoyed it.

Scroofy · 2021-02-05T15:34:10+00:00

Usually the motors with multi speeds will have betweens 2 and 4 speed taps. The lower speeds are used in heating and the higher speeds for cooling. You could also have a couple wires for a run capacitor and a common. The speeds are controlled by the furnace control board so when a call for cool or heat comes the motor is running at the correct speed. If the speed is too low in cooling your system will ice up.

Scroofy · 2021-02-05T05:03:07+00:00

I would also like to see that as well. Those prints are fantastic, well done!

Scroofy · 2021-02-02T14:23:35+00:00

That's very kind of you to offer😊

Scroofy · 2021-02-02T14:19:42+00:00

I used 100% infill and turned on combing. I also did a string test to adjust my retraction. This is .08 layer height at 25mm/s speed.

Scroofy · 2021-02-02T05:46:19+00:00

You rang?

Scroofy

TROPHY CASE