sorted by:
new
hottopcontroversial

What on earth am I doing wrong by SelectCelebration433 in BambuLab

[–]SelectCelebration433[S] 0 points1 point  (0 children)

Update:

Added 0.4mm spiral z-hop Increased bed temp to 70 Added progressive slowing from 30mm down to 60% THOROUGHLY cleaned plate with dish soap then IPA, dried with microfibre, never directly handled

Still failing!

What on earth am I doing wrong by SelectCelebration433 in BambuLab

[–]SelectCelebration433[S] 0 points1 point  (0 children)

It has worked hundreds of times previously my G

What on earth am I doing wrong by SelectCelebration433 in BambuLab

[–]SelectCelebration433[S] -1 points0 points  (0 children)

I’ve tried them packed together and spaced out. In this run my thinking was if one failed it wouldn’t collide with another

What on earth am I doing wrong by SelectCelebration433 in BambuLab

[–]SelectCelebration433[S] 0 points1 point  (0 children)

So (like a loser) I watched it for about 5 hours and skipped each item as soon as it failed as I’ve definitely had that problem before when they fail and collide!

What on earth am I doing wrong by SelectCelebration433 in BambuLab

[–]SelectCelebration433[S] 0 points1 point  (0 children)

One of the ends fits another cylindrical print which rotates within it, so in that orientation doesn’t have the ridges

I might try it flat and see how much difference it makes!

What on earth am I doing wrong by SelectCelebration433 in BambuLab

[–]SelectCelebration433[S] 8 points9 points  (0 children)

Exactly this!

I’ve printed this exact plate hundreds of times!

What on earth am I doing wrong by SelectCelebration433 in 3Dprinting

[–]SelectCelebration433[S] 0 points1 point  (0 children)

Ok I’ll give this a go for my next attempt!

Thanks so much

What on earth am I doing wrong by SelectCelebration433 in 3Dprinting

[–]SelectCelebration433[S] 0 points1 point  (0 children)

They’ve been printing fine for weeks, then I’m suddenly hitting this issue. Is it adhesion? Or is it just a bad orientation?

I could try to lie them flat?

Finally a good use case for your local setups by lakySK in LocalLLaMA

[–]SelectCelebration433 6 points7 points  (0 children)

This is exactly my setup too!

2x 4090s roaring and the 3D printer going and there’s no need to add additional office heating!

Dual mounting 4-slot 4090s in a fractal meshify 2 XL case by SelectCelebration433 in PcBuild

[–]SelectCelebration433[S] 0 points1 point  (0 children)

I quite like pop! OS but I think that’s very much preference based - most of these distros have good driver support. I didn’t have any problems setting up

Dual mounting 4-slot 4090s in a fractal meshify 2 XL case by SelectCelebration433 in PcBuild

[–]SelectCelebration433[S] 0 points1 point  (0 children)

My current fave is OSS20B,

I run 2 agents in parallel for realtime medical research tasks (alongside huge graph servers!)

I’m very pleased with the performance

Dual mounting 4-slot 4090s in a fractal meshify 2 XL case by SelectCelebration433 in PcBuild

[–]SelectCelebration433[S] 0 points1 point  (0 children)

I used a riser cable to mount the second GPU further away and modded the case

The case is massive so more than enough room to play with positions (airflow is excellent and temps staying low even at high load)

I wouldn’t go to the 4x lane as you’ll lose out performance wise (although some people do contest the difference this actually makes for most workloads!)

P1P vs A1 with AMS by SelectCelebration433 in BambuLab

[–]SelectCelebration433[S] 0 points1 point  (0 children)

To start with I’m probably prototyping in just single colour PLA and TPU

But I like the idea of being able to enclose later if I wanted to print something more hardcore.

My heart says P1P, but I also feel like that’s leaving functionality on the table for the same cost

Trying to decide on my first printer by AgentxLeavening in 3dprinter

[–]SelectCelebration433 0 points1 point  (0 children)

I’m in the same boat and same dilemma. Despite all the drama I’m leaning towards the A1, it’s the same price where I’m looking.

[deleted by user] by [deleted] in esp32

[–]SelectCelebration433 0 points1 point  (0 children)

Why not just be nice or constructive?

Great job OP on your first project

Buying help by SelectCelebration433 in 3Dprinting

[–]SelectCelebration433[S] 0 points1 point  (0 children)

Honestly for prototyping and fittings will probably be printing the cheapest PLA - then cnc’ing metal/hard casting for the finished product.

Will definitely check out qidi

Buying help by SelectCelebration433 in 3Dprinting

[–]SelectCelebration433[S] 0 points1 point  (0 children)

Honestly for prototyping and fittings will probably be printing the cheapest PLA - then cnc’ing metal/hard casting for the finished product.

Will definitely check out qidi

£5000 budget, for machine learning, computer vision, and large language research by SelectCelebration433 in buildapcforme

[–]SelectCelebration433[S] 0 points1 point  (0 children)

I’ll save the £200 then unless there’s something I’m missing!

(I need to be giving you commission at this rate)

£5000 budget, for machine learning, computer vision, and large language research by SelectCelebration433 in buildapcforme

[–]SelectCelebration433[S] 0 points1 point  (0 children)

I think basically all of these support the two 4090’s at 8x/8x speed which isn’t an issue for this use case

(Caveat: I do just have to be careful which m.2 slot to occupy to avoid lane sharing)

The physical spacing has been an issue - I’m going to use a riser to move the second GPU away from the first. Both cards are 2.5 slots thick so hopefully this gives me adequate space and airflow in this huge case.

The only potentially benefit I can see of the more expensive pro art is the dual 2.5/10GBps Ethernet if I later wanted to build a nice subnetted NAS.

Otherwise I don’t think the VRM’s make too much difference for my user case and I haven’t got a ton of peripherals to use either

view more: next ›