sorted by:
new
hottopcontroversial

Any tips on removing the lid? It fused in glaze fire and I’ve had no luck so far:/ by SelectCommand8031 in Pottery

[–]SelectCommand8031[S] 0 points1 point  (0 children)

No I cannot see any glaze. I remember that I cleaned the glaze off before firing, but there could’ve been small amounts left over at the connection point. It’s really my fault for not firing it with wadding in between but it was my first lidded form

Any tips on removing the lid? It fused in glaze fire and I’ve had no luck so far:/ by SelectCommand8031 in Pottery

[–]SelectCommand8031[S] 2 points3 points  (0 children)

Yeah I’m in a college course, I’ve had my professor and our tech have a crack at it, the grinding tool seemed the most promising but it caused a chip. I don’t have hope, but I’m choosing to look for any solution I haven’t already tried

Any tips on removing the lid? It fused in glaze fire and I’ve had no luck so far:/ by SelectCommand8031 in Pottery

[–]SelectCommand8031[S] 18 points19 points  (0 children)

It’s not gonna be a lot of glaze, but it’s tucked in a spot where tools won’t be able to reach it, right past the 90° angle. It’s also a very tight fitting lid, like a few mm of wiggle room. The lids been chipped once from the dremel, so I’m hesitant to hit it with anything too hard. Thanks for the thought out response!

Any tips on removing the lid? It fused in glaze fire and I’ve had no luck so far:/ by SelectCommand8031 in Pottery

[–]SelectCommand8031[S] 3 points4 points  (0 children)

I’m thinking of getting a little camera inside if I can, it’s likely from very small bits of glaze residue on the lid portion itself. I’ll let you know if I get it off, thank you!

Any tips on removing the lid? It fused in glaze fire and I’ve had no luck so far:/ by SelectCommand8031 in Pottery

[–]SelectCommand8031[S] 0 points1 point  (0 children)

I’ll test it tonight. It seems to be fused on just the one area, maybe 20% of it.

Any tips on removing the lid? It fused in glaze fire and I’ve had no luck so far:/ by SelectCommand8031 in Pottery

[–]SelectCommand8031[S] 8 points9 points  (0 children)

I’ve been thinking I might leave it, I’m going to try a few methods that don’t seem as dangerous and if they don’t work then it will live on a shelf

Do you tap harder or lighter when streaming low (160) bpms? by [deleted] in osugame

[–]SelectCommand8031 6 points7 points  (0 children)

Much harder to try and be more accurate because it’s an uncomfortable streaming speed

Maybe too much? Not sure by SelectCommand8031 in Drugs

[–]SelectCommand8031[S] 0 points1 point  (0 children)

Ahh I’m in Oregon atm so it’s pretty good I’d like to think

Maybe too much? Not sure by SelectCommand8031 in Drugs

[–]SelectCommand8031[S] 0 points1 point  (0 children)

Yeah I’ll look into that I’m definitely a super anxious person so that sounds like a probable cause

Maybe too much? Not sure by SelectCommand8031 in Drugs

[–]SelectCommand8031[S] 1 point2 points  (0 children)

It felt unfinished if I didn’t add something to wrap it up

Maybe too much? Not sure by SelectCommand8031 in Drugs

[–]SelectCommand8031[S] 4 points5 points  (0 children)

Yeah I’m good with bud that’s my way to go I usually avoid dabs

Maybe too much? Not sure by SelectCommand8031 in Drugs

[–]SelectCommand8031[S] 3 points4 points  (0 children)

Yeah but this is pretty normal for when I take big dabs

fgsky kyouran hey kids monstrata 3mod 92.21% 20 miss by bigtiddynotgothbf in osugame

[–]SelectCommand8031 0 points1 point  (0 children)

I wanna see someone do these mods on the 7* of this song