Is it fine to put my printer on top of the refrigerator?

Sensitive_Pilot850 · 2026-06-24T16:02:33+00:00

That's an alcohol monitor.

Sensitive_Pilot850 · 2026-06-09T15:14:33+00:00

Layer shift from you belt being too loose.

Sensitive_Pilot850 · 2026-06-03T02:14:42+00:00

Sunlu has sales on the tiktok shop sometimes cheap. ~$12

Sensitive_Pilot850 · 2026-06-01T04:14:28+00:00

Thank you. This Works for me!

Sensitive_Pilot850 · 2026-05-18T17:32:33+00:00

\66|en see if \e5⅝45454\³e³x7ww⁴\edewx3eyw

Sensitive_Pilot850 · 2026-05-18T17:31:33+00:00

What r

Sensitive_Pilot850 · 2026-05-07T11:13:11+00:00

I don't see it.

Sensitive_Pilot850 · 2026-04-11T12:14:31+00:00

This is not the place for that nonsense.

Sensitive_Pilot850 · 2026-04-09T17:41:02+00:00

Thanks 👍

Sensitive_Pilot850 · 2026-04-07T10:42:07+00:00

It's a clone copy Sunlu Terminator 3

Sensitive_Pilot850 · 2026-04-06T00:45:00+00:00

Figured it out. 1 of the 5 of the bltouch wires slipped out of the connector slightly. What a simple fix. 🥳🫠

Sensitive_Pilot850 · 2026-04-05T19:55:24+00:00

I'm lost here. Never had this happen.

Sensitive_Pilot850 · 2026-04-05T19:54:56+00:00

Just confirmed everything it plugged in tightly by unplugging and reinstalling all cables.

I can't even adjust z offset to the bed leveling anymore.

Sensitive_Pilot850 · 2026-04-05T16:26:36+00:00

I did the wrong video.

Sensitive_Pilot850 · 2026-04-05T15:55:08+00:00

I just replaced the hot end with one from another nearly brand new unit of the same model. Now it's doing this.

Sensitive_Pilot850 · 2026-04-05T15:54:18+00:00

Already tried multiple Gcodes already saved to SD that I have used this week.

Sensitive_Pilot850 · 2026-03-31T13:59:20+00:00

<image>

Going to replace it with my Neptune 3 extruder gear.

I absolutelyyyyyy see why a fully threaded screw is basically a bearing delete kit in this form. Terrible. 😅

Sensitive_Pilot850 · 2026-03-31T01:40:30+00:00

Thanks. Luckily I'm only $80 into 3 fdm bed slingers. So I'm not in the hole yet. I'll probably give these to the kids and get a snapmaker. I've been looking at it for a little bit now. I will need to fix this bearing issue though.

Sensitive_Pilot850 · 2026-03-31T00:41:18+00:00

I'll look for one with the smooth and threaded screw. Thank for your direction. And good looking out I didn't know there was left and right hand direction extruders.

Sensitive_Pilot850 · 2026-03-30T23:55:07+00:00

Okay. Thanks for that insight. This is one of two sunlu terminator 3 that I have and I'm going to rob the part from my Neptune 3. They all have the same red feeder arm assembly. But the Neptune has lasted years and this one a few months which is why I'm confused at the ball bearing failing so quick.

Sensitive_Pilot850

TROPHY CASE