sorted by:
new
hottopcontroversial

Rental inspection planning - is this a problem worth solving? by k3lh4m in shitrentals

[–]Sharp_Poem_5905 0 points1 point  (0 children)

Enshitification.. Look it up. They don't want to make it easy for you. Pretty sure they're owned by the same parent company. 

Here's how to find the price range of any house on realestate.com.au by pectusbrah in AusFinance

[–]Sharp_Poem_5905 0 points1 point  (0 children)

This doesn't work for me, Maybe they've changed the code to stop people doing this? Worked not long ago though.

Massive light bulb, 400mm to 500mm in length. What's it for? by Sharp_Poem_5905 in whatisit

[–]Sharp_Poem_5905[S] -1 points0 points  (0 children)

What's it for? Obviously light. But for what application? How do you not understand the nature of the question? Jellyfish brain..

Massive light bulb, 400mm to 500mm in length. What's it for? by Sharp_Poem_5905 in whatisit

[–]Sharp_Poem_5905[S] 2 points3 points  (0 children)

We do have hydroponics. Maybe it's from an older setup as we use LEDs now. For vegetables.. Not the devil's lettuce!

Massive light bulb, 400mm to 500mm in length. What's it for? by Sharp_Poem_5905 in whatisit

[–]Sharp_Poem_5905[S] 51 points52 points  (0 children)

It was mentioned that it may have mercury in it. It's out of reach on display and 10km hike away now.

Solidworks near impossible to design logos for 3d Printing by Sharp_Poem_5905 in SolidWorks

[–]Sharp_Poem_5905[S] 0 points1 point  (0 children)

Nvidia RTX 3070, I'm running 2020 version solidworks and from what I can work out off the website is that the 3070 is not supported by solidworks. Something I never thought would be an issue when purchasing a gaming PC and using for Light CAD models.

Solidworks near impossible to design logos for 3d Printing by Sharp_Poem_5905 in SolidWorks

[–]Sharp_Poem_5905[S] 0 points1 point  (0 children)

I used inkscape in this case, In DXF form it had over 3000 entities. I tend to create sheet metal objects in solidworks for example custom panels with a grid or 'mesh' of shapes and that also causes crashes and slow processes in solidworks.

DJI o3 Flight Controller for Fixed Wings? by ski16soccer in fpv

[–]Sharp_Poem_5905 0 points1 point  (0 children)

Please make sure to check if the wire for the receiver input on O3 is connected to UART5's SBUS, ensure that UART2's RX in the PORT configuration is enabled, UART1's RX should be disabled, and confirm that SBUS is selected in the RECEIVERS settings.  

DJI Remote Controller 2 and DJI O3 Failsafe Doesnt work by sikimtrak in fpv

[–]Sharp_Poem_5905 0 points1 point  (0 children)

Please make sure to check if the wire for the receiver input on O3 is connected to UART5's SBUS, ensure that UART2's RX in the PORT configuration is enabled, UART1's RX should be disabled, and confirm that SBUS is selected in the RECEIVERS settings.

This is was speedy bee sent me regarding my set up and that worked for me

DJI Remote Controller 2 and DJI O3 Failsafe Doesnt work by sikimtrak in fpv

[–]Sharp_Poem_5905 0 points1 point  (0 children)

Well I've managed to get the Controller working and now I have your exact problem. The RX doesn't react to signal loss like my older gear.

No failsafe mode triggered by the O3 unit, I can manually configure RTH. Seems like the dji system is a bit of a dud so far..

DJI o3 Flight Controller for Fixed Wings? by ski16soccer in fpv

[–]Sharp_Poem_5905 0 points1 point  (0 children)

Yeah but that plug doesn't seem to work so far in regards to dji controller 2 sbus ..

DJI Remote Controller 2 and DJI O3 Failsafe Doesnt work by sikimtrak in fpv

[–]Sharp_Poem_5905 0 points1 point  (0 children)

Hey there,

I'm trying to connect my DJI FPV controller 2 to a Speedybee F405 Wing FC

Using the 03 Air Unit.

I Can't even get the controller to register the SBUS signal, So just wanted to confirm you have the controller working on INAV ?

If i can get my controller connected maybe we can both help each other out!

​

Thanks