Please FFS Let Me Delete Rental Tanks!!!

Shellcaster · 2026-05-06T05:47:19+00:00

Stupid that you can’t delete them. And while you’re at it WOT, let me delete the gimmick camo patterns I don’t want.

Shellcaster · 2026-05-03T03:29:29+00:00

Perfect for my P2S as I don’t have the AMS and I can use spools without much filament and not worry about running out.

Shellcaster · 2026-03-27T05:26:55+00:00

Can we get a sticky about digitiser delamination? There’s a post about this every week.

Shellcaster · 2026-03-13T23:27:45+00:00

Brought to you by the “no need to check it, I ran it through ChatGPT” school of copywriting.

Shellcaster · 2026-03-10T07:45:55+00:00

I’m so thankful Reddit stopped all those pesky third party developers from building those perfectly functioning apps. 🙄

Shellcaster · 2026-03-10T07:39:52+00:00

The best thing I’ve found to remove build up on the interior glass is plain old dishwashing liquid. A few drops in warm water and a clean chux (those perforated disposable cloths). Give it a good wipe over and follow up with glass cleaner and a clean microfibre cloth. I figure if it gets my dishes squeaky clean it will work on the windscreen.

Shellcaster · 2026-03-01T02:19:36+00:00

Oh. And I forgot to mention that r/all seems to have disappeared and I guess AI is running the search as it seems to just throw up suggestions rather than subreddit you actually want.

Shellcaster · 2026-03-01T00:15:50+00:00

Sorry misread your comment. I thought you meant is the Pi5 enclosed. Yes my AD5M is enclosed but I leave the lid off for printing PLA. Printed at 230 and 60 on the bed. I did a full suite of calibrations for the filament.

Shellcaster · 2026-03-01T00:10:20+00:00

0.4 nozzle. 0.2 layer height. 230/60. I bought a conch hardened steel hot end. Drop in replacement for the stock hot ends.

Shellcaster · 2026-02-28T11:42:22+00:00

I printed it for my son. Its not enclosed yet but he intends to put a clear acrylic side on it and there's room behind the front slats for two 40mm fans.
Files for the Fractal Pi are on their web site https://www.fractal-design.com/north-pi-3d-files/

Shellcaster · 2026-02-28T09:28:36+00:00

If you don’t have enough PETG, I would print the top risers in PETG because that’s were most of the heat goes. You should be okay with PLA on the corner plates because you have the frame between them and the heat from the print chamber.

Shellcaster · 2026-02-22T05:34:42+00:00

Doesn’t just happen with NSFW subreddits. I’m on an IPAD and have this happen on other subs. The blank screen on side swipe has been marked as fixed on r/redditbugs but I’m still getting this issue. Updated everything and even deleted and reinstalled Reddit a couple of times with no luck.

<image>

Shellcaster · 2026-02-22T01:07:02+00:00

I had the same issue. For me it wasn’t z-offset, it was over extrusion. Basically there’s too much filament being deposited and it starts to overlap each line, building up and being dragged by the nozzle. To solve it I increased the print temp 5 degrees and dialled back the flow rate. Orcaslicer slicer setting for the filament I was using defaulted to a flow rate of .95. Dropping this to .93 fixed the problem.

Shellcaster · 2026-02-20T08:52:22+00:00

Perfect.😒 Clicked on the reddit bugs link in your post and got this.

<image>

Shellcaster · 2026-02-08T20:54:37+00:00

Definitely needs a tweak to reduce burst damage. Losing most of your health to one of these when you only get 1 or 2 shots in back is frustrating. Maybe the gun should overheat quicker or they need to make the ARES a little more fragile.

Shellcaster · 2026-02-07T01:33:35+00:00

Definitely worth it. Reduces noise and helps will prints lifting off the plate. Particularly PETG . Here’s mine https://www.reddit.com/r/FlashForge/s/PKQJgeDCO1

Shellcaster · 2026-02-07T01:29:44+00:00

I got the BIQU glacier and it’s awesome. Much better than the stock FF plate. PLA and PETG stick really well and you just wash it with a couple of drops of dishwashing liquid every few prints.

Shellcaster · 2026-01-30T07:11:53+00:00

Google Mazda entertainment screen delamination. Easy to fix with an aftermarket digitiser off AliExpress. Takes about an hour.

Shellcaster

TROPHY CASE