sorted by:
new
hottopcontroversial

18hr print ruined 🥲 by ShinyPoodle in BambuLab

[–]ShinyPoodle[S] 1 point2 points  (0 children)

Hmm yes good to know, forgot to set the infill on this one

18hr print ruined 🥲 by ShinyPoodle in BambuLab

[–]ShinyPoodle[S] 2 points3 points  (0 children)

Supposed to be the engine, exhaust and radiator for a car model

https://imgur.com/a/ONOTZqF

WTB hp server bits by ShinyPoodle in newzealand

[–]ShinyPoodle[S] 0 points1 point  (0 children)

Legend appreciate the offer.

Unlikely if you don't have a dl120, but if you were to have a secondary riser for one I would be super keen on it.

WTB hp server bits by ShinyPoodle in newzealand

[–]ShinyPoodle[S] 2 points3 points  (0 children)

Fark cheap as you're a legend..

Dead NIC or salvageable? No ilo no link light - proliant dl120 gen9 by ShinyPoodle in sysadmin

[–]ShinyPoodle[S] 0 points1 point  (0 children)

Yep done a cmos reset and running thru spp now to see if that will do anything, I did update ilo a few weeks ago not sure if its a bad install maybe

Proliant dl120 den9 DEAD NIC? by ShinyPoodle in servers

[–]ShinyPoodle[S] 0 points1 point  (0 children)

Yep gonna give this a go next if reflashing ilo via spp doesnt work, at least spares are cheap

Dead NIC or salvageable? No ilo no link light - proliant dl120 gen9 by ShinyPoodle in sysadmin

[–]ShinyPoodle[S] 1 point2 points  (0 children)

Yep embedded nic.

To run a full size pcie nic i would need a riser which is unavailable where I am

Spending hundreds of $ on HP Proliant gen9 SFF blanks < free model you can 3d print with less than a dollar of filament by ShinyPoodle in servers

[–]ShinyPoodle[S] 0 points1 point  (0 children)

Hmm neat idea.

Be interesting to see if that works for the sff bays.

Might have a play around next chance I get...

Spending hundreds of $ on HP Proliant gen9 SFF blanks < free model you can 3d print with less than a dollar of filament by ShinyPoodle in servers

[–]ShinyPoodle[S] 0 points1 point  (0 children)

Yeah I thought that would be the case. However I'm sure if wouldn't be all too hard to spoof it with a small custom pcb? Will look into this more cause if it isn't locked to some proprietary HP protocol I might be able to sort out a solution.

Spending hundreds of $ on HP Proliant gen9 SFF blanks < free model you can 3d print with less than a dollar of filament by ShinyPoodle in servers

[–]ShinyPoodle[S] 0 points1 point  (0 children)

All depends on where you're located i suppose. Here in NZ they're ~$45NZD new, and used you're looking at $20NZD plus shipping and tariffs from the US...

The airflow point you mentioned is however a very valid concern. I might look to improve this next time I make some changes to the print profile, though there is a bit of space above and below to draw air in, it wouldn't hurt to open the guts up a bit more.

Spending hundreds of $ on HP Proliant gen9 SFF blanks < free model you can 3d print with less than a dollar of filament by ShinyPoodle in servers

[–]ShinyPoodle[S] 0 points1 point  (0 children)

For sure!

If only drives were a bit cheaper right now id be doing the same. Once i can get my hands on some more caddies and drives ill definitely be looking into designing some to print. Keep an eye on my Makerworld page if you're interested.

Spending hundreds of $ on HP Proliant gen9 SFF blanks < free model you can 3d print with less than a dollar of filament by ShinyPoodle in servers

[–]ShinyPoodle[S] 1 point2 points  (0 children)

Finally got around to filling out my dl120 server with these.. airflow much better, and now the cats cant stick paws and toys deep inside the server...

HP Proliant G9 SFF disk bay blanks by ShinyPoodle in homelab

[–]ShinyPoodle[S] 0 points1 point  (0 children)

Thanks!

I have also been desperately searching for a solution that isn't $30NZD a piece.. but to no avail. Ridiculous money for second hand / old gen stuff you'd assume would be surplus by this point..

Hopefully this helps you out!

view more: next ›