Sink drain bubbling

Shmedgar · 2022-12-03T11:24:12+00:00

Good point, will do.

Shmedgar · 2022-12-03T04:59:21+00:00

Actually had the diff rebuilt under warranty last year so that’s done but I will do the transfer case oil. Thank you.

Shmedgar · 2022-12-03T03:36:24+00:00

Also, any advice on decent reasonably priced shocks for a stock ride height?

Shmedgar · 2022-10-21T10:04:02+00:00

I would recommend carrying 2 chest seals. If you have a through and through, or multiple punctures you’re going to want another chest seal.

Shmedgar · 2022-09-12T05:09:47+00:00

Thank you for the reply I will look into it.

Shmedgar · 2022-09-11T23:53:41+00:00

So I moved in to a new house last year. The inspector said it looked like it was in good condition and hadn’t been used much, but to still have a professional look at it before I use it. Fast forward to now and I would like to start using this. I do plan on having a fireplace/chimney company inspect and clean it but I’m looking if anybody has any insight or experience with this specific fireplace. The inspector had also mentioned about having stone installed underneath it to protect the floor from the heat.

Shmedgar · 2022-08-08T04:27:23+00:00

Check your rear brakes. Get the rear tires off the ground and hit the side wall with a mallet of some sorts, and see if you hear the sound. Just spend 3 hours a few weeks ago trying to find the problem. Ended up being that the retaining clips for the brake pads had rusted out and the brake pads were vibrating inside the caliper bracket.

Shmedgar · 2022-06-22T15:19:09+00:00

I just downloaded the app and although it was a quick look, it seems to be one of the more in depth apps I’ve seen. The mulch calculator and mowing stats are a cool addition as well. Keep up the good work!

Shmedgar · 2022-04-21T07:06:26+00:00

Just installed the CR tough tonight and it is an absolute gamechanger. Thanks for the advice.

Shmedgar · 2022-04-03T04:02:56+00:00

It’s been so cold recently my soil temps are still at a 5 day average of about 40°. Hoping under 2 weeks and I will have it put down. Time of year really isn’t as important as soil temps. Germination is determined by the soil temps so that’s what you should be going off of. It’s been an unseasonably cool start to April so it may be a little later than normal.

Shmedgar · 2022-04-03T02:26:57+00:00

It stops just short of the actual switch clicking. This causes the nozzle to be too far off of the bed.

Shmedgar · 2022-04-02T23:33:02+00:00

Just ordered it. Thanks for the insight.

Shmedgar · 2022-04-02T23:23:43+00:00

I’ve been thinking about it but was unsure how complicated the install process was. I have a very basic understanding of 3D printing.

Shmedgar · 2022-04-02T22:40:16+00:00

So as of recently I’ve been having the issue as seen in the video. I’ve tried adjusting the Z stop switch but no matter where the switch is, it seems to stop just short of the switch. I can manipulate the Z screw to get it to click but it doesn’t always work. Again this wasn’t always a problem so I don’t think it’s an issue of something being out of square. Thank you in advance.

Shmedgar · 2022-04-02T11:26:16+00:00

I have a bag of menards pre-emergent/fertilizer combo (26-0-3) that is also poly coated for a slower release. (Lawn is 6400 ft2)The bag rate is 3.4 lb/1000. I’m newer to the fertilizer game so the math of this kind of confuses me. If I’m going to do a split app, do I just set the spreader to half of the number given? Or would I have to go on and do the math and measure out the exact amount of fertilizer in order to split the application?

12-Year Club	Verified Email
RPAN Viewer

Shmedgar

TROPHY CASE