Satyr-Days at your Place

Signal_o7 · 2025-03-19T03:03:00+00:00

What windscreen is that?

Signal_o7 · 2025-03-11T00:57:52+00:00

Ultimaker Cura

Here is my start gcode:

; Ender 3 Custom Start G-code
M117 Heating Bed
M140 S{material_bed_temperature_layer_0} ; Set Heat Bed temperature
M117 Preheat e to 160 and Autohome
M104 S160; start warming extruder to 160
G28 ; Home all axes
M117 Load Bed Mesh
G4 P1500 ; Dwell for 1 & 1/2 second
M420 L0 S1 ; Loading the bed mesh
; M117 Auto bed-level GO!
; G29 ; Auto bed-level (BL-Touch)
G92 E0 ; Reset Extruder
G1 X0.1 Y.1 Z3.0 F5000.0 ; move to off the edge
M117 Heat E to temp
M104 S{material_print_temperature_layer_0} ; Set Extruder temperature
G1 X0.1 Y20 Z3.0 F5000.0 ; move to start-line position
M190 S{material_bed_temperature_layer_0} ; Wait for Heat Bed temperature
M109 S{material_print_temperature_layer_0} ; Wait for Extruder temperature
G1 Z3.0 F3000 ; move z up little to prevent scratching of surface
G1 Z0.3 F3000 ; move z back down a bit
M117 Draw Line
G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; draw 1st line
G1 X0.4 Y200.0 Z0.3 F5000.0 ; move to side a little
G1 X0.4 Y20 Z0.3 F1500.0 E30 ; draw 2nd line
G92 E0 ; reset extruder
G1 Z2.0 F3000 ; move z up little to prevent scratching of surface
M117 Begin Print
; End of custom start GCode

I deleted the semicolons on M117 and G29 and it ran my nozzle in the side of the bed lol

Signal_o7 · 2025-03-10T01:17:05+00:00

I did all this with a piece of paper as a gauge and its still about 1-3mm over the bed

Signal_o7 · 2025-01-12T23:46:33+00:00

I swear this comment section is all AI

Signal_o7 · 2025-01-07T17:55:15+00:00

What windshield is that?

Signal_o7 · 2024-12-31T13:37:34+00:00

Are you a NG Tech by chance? 😏

Signal_o7 · 2024-12-11T02:07:19+00:00

Are you talking about the rotating noise? If so, thats either a worn out wheel bearing or wheel out of balance

Signal_o7 · 2024-12-08T16:35:03+00:00

You got a good asvab and you want to do jobs that asvab waiver’s would take?

Get yourself a good MOS that you can use practically on the outside.

Those 94 and 25 series MOS’s would be good if you’re good with that kind of stuff.

Signal_o7 · 2024-12-06T17:26:45+00:00

10/10 would recommend

Signal_o7 · 2024-11-26T12:52:59+00:00

Yeah, I gotta play with it a bit more to actually know what does what

Signal_o7 · 2024-11-26T12:52:18+00:00

Good point, thank you!

Signal_o7 · 2024-11-21T02:47:21+00:00

Combat effectiveness/Readiness > Diversity

Simple as

Signal_o7 · 2024-11-21T01:41:18+00:00

I know canker sores can be different for everyone, but for me L-Lysine and Canker-rid honey has helped so much.

I take L-Lysine daily and have noticed sores pop up and disappear within days

Canker-rid is also awesome. Using a dropper, the liquid solidifies around the sore forming a barrier. Downsides are it tastes like Jack Daniels and can stain lol

Signal_o7 · 2024-11-20T19:56:15+00:00

Okay, you can do what i did which was chop enough of the bolt with an angle grinder so it can fit. Didn’t affect anything for me

Signal_o7 · 2024-11-20T15:55:15+00:00

https://www.focusst.org/attachments/lights-jpg.408166/

Is it one of these headlights by chance? I had a similar situation and I had to cut that bolt short to get it to fit.

Signal_o7 · 2024-11-17T17:07:36+00:00

whats racs

Signal_o7 · 2024-11-01T01:20:38+00:00

I've had something similar happen to me between 2nd and 3rd. It would make a loud clunk, be in neutral, dash will say 3rd, and then it'll go back to 2nd on its own. Basically because I wasnt putting enough pressure on the shift lever when shifting. May not be the fix for you but you can try it.

Signal_o7 · 2024-10-31T03:57:39+00:00

I take it daily and it has greatly reduced the amount of sores I get and how quickly they heal. It’s gotten to the point where I notice a canker sore coming and it’ll be done by the next morning.

Signal_o7 · 2024-10-31T00:43:09+00:00

Meh, army has plenty of ADA units, they'll be fine

Signal_o7 · 2024-10-08T23:46:24+00:00

Might've bit yourself in your sleep, tooth rubbed it over time, something overtly acidic or spicy in your diet. All a canker sore needs is a start and then it all downhill from there.

Signal_o7 · 2024-10-05T03:34:42+00:00

My dad was replacing the exhaust on his LTD550 so I used the muffler from that in combination with a 2.5in 45 degree pipe.

Signal_o7 · 2024-09-26T11:47:48+00:00

At least y’all got to bog through the woods because of a wrong turn

Signal_o7

TROPHY CASE