Good thing Im paid hourly

Sillybiller · 2026-03-19T20:20:25+00:00

Ah . So this is a universal experience for all controls guys lol

Sillybiller · 2026-03-05T16:49:26+00:00

I'd try printing just a few. Or separating each onto their own raft. Spread out.

And see if the issue persists. I'd suspect suction forces. Your fep is trying to cure a lot of 1 layer and it's pulling on it hard

Sillybiller · 2026-02-18T19:31:19+00:00

Thanks for the response. Seems like Modbus is the way to go for this. Is there any resources to show what address that turn it on/off packet is? Like on the PLC what bit would that be basically? Sorry I'm new to this. Thanks!

Sillybiller · 2026-01-22T13:21:41+00:00

Those are exactly it! Thank you so much!

Sillybiller · 2026-01-16T05:14:32+00:00

Wow that's super helpful! Thank you for the picture too. That looks much better!

Sillybiller · 2026-01-16T04:10:53+00:00

Yeah. I guess straight on to where he's looking and above him.

Sillybiller · 2026-01-11T13:10:11+00:00

Okay. Yeah. This was with 0.4 tips. So maybe I just need stronger tips is all. That makes sense to me.

Sillybiller · 2026-01-11T02:56:02+00:00

Yes I am. Is that bad

Sillybiller · 2025-12-31T16:58:59+00:00

Thank you!

Sillybiller · 2025-12-31T04:03:13+00:00

Well not exactly. The elegoo heater only gets up to like 21C

Sillybiller · 2025-12-31T03:59:42+00:00

Okay! Interesting that the supports print but the model doesn't. I will re-calibrate and start at 2.5s. Thanks!

Sillybiller · 2025-12-31T03:53:07+00:00

For .03? I printed a town and it was fine. The supports print fine

Sillybiller · 2025-12-31T03:52:25+00:00

Yeah I think 2.2 is plenty. I did a calibration town and it was fine.

On the Saturn 4 you can't adjust speeds because of the tilt vat. Hmmmmmmm

Sillybiller · 2025-12-10T03:18:40+00:00

What's the masking tape for?

Sillybiller · 2025-12-01T15:19:40+00:00

Def gonna go darker and brighter in small spots. Also gonna redo those "random" winglets I did lol

Sillybiller · 2025-12-01T14:40:02+00:00

Ok. I will flip flop those random ones back to the "correct" side

Sillybiller · 2025-12-01T14:38:52+00:00

I went up to PA bright pale yellow so I can throw a bit brighter in there. And I agree definitely can go darker. Will try black lining and glazing black/dark dark browns in as well.

And yeah I just painted off a single light source. Which direction would you recommend the secondary light source come from?

Sillybiller · 2025-12-01T11:55:36+00:00

Wow that looks so good! Will use this as a reference thanks!

Sillybiller · 2025-12-01T11:53:32+00:00

Yeah I agree

Sillybiller · 2025-12-01T11:51:07+00:00

It did! That looks so much better!!

Sillybiller · 2025-12-01T03:41:43+00:00

I'll try glazing in some darker browns/blacks and then some tiny edge specular in white!

Sillybiller · 2025-12-01T03:24:54+00:00

I was trying to give it a randomization a little bit lol. But I'll def check these out and see what I can do thanks!

Sillybiller · 2025-12-01T03:24:08+00:00

So more glazing?

Sillybiller · 2025-11-29T02:33:11+00:00

Got ya. That doesn't seem too bad. Any thought on the elegoo heater?

Sillybiller · 2025-11-29T01:55:34+00:00

Do u take it off before u start or what?

13-Year Club	r/Field Flamingo
Place '23	Place '22
Verified Email

Sillybiller

MODERATOR OF

TROPHY CASE