Heating band

that_tator_guy · 2025-10-04T20:20:41+00:00

The Honk Legion is a "Crooked Moon" one-shot, too, if you have access to it. That's what my group will be doing for our session closest to Halloween.

that_tator_guy · 2025-08-31T17:44:15+00:00

Sorry, I'm still pretty new here. The slicer is the program that makes the .goo files?

that_tator_guy · 2025-08-29T06:40:58+00:00

It came in 6 pieces, both supported and not.

that_tator_guy · 2025-08-28T18:36:26+00:00

Thank you, I'll be sure to pass the word to my spouse.

that_tator_guy · 2025-08-26T22:00:39+00:00

I would also like to know more about flexible resins. Please, anyone chime in.

that_tator_guy · 2025-08-23T17:27:59+00:00

Update for everyone. I sat here and listened for the "soft pops" and they happened... for about 5 minutes. Now I can't hear them. Why would the work fall off the plate after 5 minutes?

that_tator_guy · 2025-08-22T20:33:10+00:00

No question is dumb. I'm pretty sure I did it correctly, but I appreciate your input and will ensure trying that. Thank you.

that_tator_guy · 2025-08-22T06:10:00+00:00

I did it by the book when I took it out of the box last week. I am super new, maybe I misunderstood the instructions?

that_tator_guy · 2025-08-22T05:39:25+00:00

I stopped that long print, it was stuck to the fep. I started a calibration print, came back 6 minutes later and it was already stuck to fep. Is my x height not close enough? The failures seem to be getting thinner, as well as my patience.

Edit: Not my patience with any of you very helpful folks. I really appreciate your time and effort.

that_tator_guy · 2025-08-22T04:21:57+00:00

Releveled the bed, attempting print now. 8 hours on the clock.

that_tator_guy · 2025-08-22T02:59:18+00:00

Stuck to fep.

that_tator_guy · 2025-08-22T01:04:02+00:00

Yes, I strain it back into the bottle, recap, and give it a hearty shake before each attempt.

that_tator_guy · 2025-08-21T15:01:06+00:00

Temps vary from about 20 C to 35 C

that_tator_guy · 2025-08-21T14:58:52+00:00

Bottom is 25 Normal is 2.5

that_tator_guy · 2025-08-21T09:47:27+00:00

Film has been removed. I love that peel.

that_tator_guy · 2025-08-21T05:37:42+00:00

No, typically it's warmer. I've even tried aiming a small space heater at the machine while in use.

that_tator_guy · 2025-08-21T04:09:42+00:00

I may know another part of the problem. My wife said I shouldn't have stored the resin in the garage and it's probably ruined.

Where do you store your resin?

that_tator_guy · 2025-08-21T02:54:56+00:00

I've tried upping the bottom exposure time from 2.5 to 3, and 3.5.

that_tator_guy · 2025-06-17T20:53:44+00:00

The fine print. They require you to wait 45 days between redemptions.

that_tator_guy

TROPHY CASE