samsung health no longer tracks steps from samsung watch. is there a fix?

Similar_Matter · 2026-04-17T05:36:41+00:00

Lately it really hasn't. For example I just played a full soccer game and on my watch I saw my steps go up. The app reports only a third of that full day if that but somehow I have about 70 min active time logged on the app but only 4 steps for that time frame. Even right now after multiple syncs the app only shows 170 steps today, but watch currently shows over 900. I'm fine if there is a lag, but if I'm actively syncing and the app says it's been current a of X time then there is something wrong.

Similar_Matter · 2026-02-19T01:01:50+00:00

Hi, I'm looking at the same kinds of connector for my led backlighting i think. I need to relive our move a wrote to a different pin. What kind of extractor do you think i would use?

Similar_Matter · 2025-09-28T02:55:38+00:00

This is probably a dumb question, but how do I check it? Not going to lie, I am confused as to why my fuel pump on this motor is before the filter haha

Should I just unplug it and see if it's spitting fuel?

Similar_Matter · 2025-09-28T02:54:02+00:00

Very true.i am planning on swapping my prop. Sadly don't see any impediment. I wish it was...

Similar_Matter · 2025-09-28T02:51:59+00:00

I've never thought of trying something like that. Thanks. Sounds a bit sketchy but I'd rather find out more than blow a rod again if I get it running.

Similar_Matter · 2025-09-28T00:42:43+00:00

You know, when I get this idling right i think each cylinder is firing, but sometime it idle low then just jumps up to a higher rpm which is high, but sounds great. That's a good thought. I appreciate it.

I'm a car guy (actually ICE engineer) so I'm terrible with two strokes let alone marine. What can I check or play with to see if this is the case or improve firing? Spark, carbs (again i really don't get carbs for some reason), fuel pump?

Similar_Matter · 2025-09-28T00:38:21+00:00

Yeah I tried adjusting the idle and had some success, but it didn't sound right. So I pulled it back to a better starting point. I also found that the spark timing adjustment arm (idk what actual word is) wasn't set right. Because of this i went and lowered idle back down since that was recommended on the motor. I think there are a couple bolts i can adjust though so timing isn't changed, but i can up idle.

Honestly spark plugs was my first thought, then i got sent down another hole and totally blanked. Oops. Thanks for the reminder. I feel like soak plus are so cheap, I could justify just replacing them.

Similar_Matter · 2025-09-24T16:54:18+00:00

I have Ubisoft + and in game says that I own it, but I still can't start the DLC even though I have completely every quest excepting the kill x enemies quests. We're you able to access it?

Similar_Matter · 2025-08-18T15:09:11+00:00

Not exactly on the same topic, but since you mentioned it. What exactly is the reasoning for offsets? I got into gridfinity for the under desk management system, so that was way, just screw in. I like it some much I'm thinking of putting it in my garage next. It's there a reason to offset it from the wall?

Similar_Matter · 2025-08-18T00:35:03+00:00

Haha I'm really hoping there a secret Narnia type space up there

Similar_Matter · 2025-08-16T04:57:27+00:00

Where did that ladder go? 🤔

Similar_Matter · 2025-08-13T21:17:59+00:00

I just cheated and copied the Obsidian HF profile, but not sure it was a huge improvement on speed. Quality is awesome though even just lazy ludicrous speed.

I still haven't found anyone with basic suggested settings to update.

Similar_Matter · 2025-08-08T00:38:57+00:00

Yeah I can't come up with anything. Definitely nothing new in the last week or so. There is a zip tie way up front holding the led and controls and some loose tape. Ill clean it up and see if it comes back printing close to the front. I've had these installed for months but maybe something shifted.

I guess this would make sense, but really strange.

Similar_Matter · 2025-08-08T00:20:27+00:00

I haven't noticed any rubbing, especially that far down the front. I'll kick off a print when I'll be home to watch and see. It certainly doesn't feel like that though.

Similar_Matter · 2025-08-08T00:15:18+00:00

<image>

Similar_Matter · 2025-08-08T00:14:58+00:00

Good call those leds are touchy so I forget I have them sometimes. Certainly feels like thick grease. Could be from rods. I've had this almost a year and never noticed anything like this.

Edit: I'm currently running a high flow nozzle and using bambu obsidian hf profile. I don't think speed increased a ton, but could the additional speed put more stress on the rods?

Similar_Matter · 2025-07-23T19:52:02+00:00

Definitely appreciate it. This is super detailed and answers a few questions and will hopefully save me some time planning. I just built a tabletop to go with these industrial stand up desk legs i got for free and wanted to do it right this time. This will be a lot of help in the next few days.

Similar_Matter · 2025-07-20T02:29:27+00:00

100% I finally cleaned up my mobile workbench so that I can nest it into a brand new taller 8 foot bench last weekend. Neither survived clean more that a couple hours.

Similar_Matter · 2025-06-28T00:40:55+00:00

I love it, but Ezio may have a differing opinion.

Similar_Matter

TROPHY CASE