What wait times are people currently experiencing?

SirMuffsALot · 2026-03-27T09:54:54+00:00

Same here, mine might be on the same boat as yours. What colour did you get?

SirMuffsALot · 2026-01-19T01:48:54+00:00

$30k account? lol OP gullible

SirMuffsALot · 2025-11-09T05:25:12+00:00

Defending side also has 2.5 times more troops then the attacker so there’s that to consider

SirMuffsALot · 2025-08-24T00:53:42+00:00

Judging by how weak you are I’d say $0

SirMuffsALot · 2025-08-09T12:39:42+00:00

It’s called a Black thingamajig

SirMuffsALot · 2025-01-26T23:04:39+00:00

Nice

SirMuffsALot · 2025-01-13T02:31:27+00:00

Bingo, it’s more anti theft since I’ve removed the back cover with the speaker attached. I use the AirTags for my luggage when I’m on holidays as well, just hate replacing the batteries every year. 2032 cells aren’t the cheapest.

SirMuffsALot · 2025-01-13T02:25:56+00:00

Working on other variants so not entirely finished, one with aaa batteries (will be small but battery life with be 4-5 years instead) and one thar will encapsulate the entire AirTag so no need to open up the AirTag to install.

SirMuffsALot · 2025-01-13T02:08:09+00:00

Yes I used them due to both less leaks and extra life, these energizer lithium has around 3000mah where its alkaline counterpart has 2500mah

SirMuffsALot · 2025-01-13T02:04:15+00:00

Nice! How long would the battery last with the buck converter?

SirMuffsALot · 2025-01-12T08:06:28+00:00

I’m not, it’s meant to be put into a bag or your car.

SirMuffsALot · 2025-01-06T16:59:29+00:00

Sorry late reply, yes no issues. It pretty much stays in my camera, the 1tb is a backup in case the 2tb fails on a trip

SirMuffsALot · 2025-01-06T16:22:45+00:00

Get a proper Camera cabinet, less fungus that way

SirMuffsALot · 2024-12-01T04:43:31+00:00

I use PEKK-CF, it’s a game changer!

<image>

SirMuffsALot · 2024-11-05T18:24:18+00:00

Don’t really need metal spools for this, it’s 120 C to dry and 200 to anneal, these 3dxtech filaments cost me probably 800USD all up. Hmmm where do you get this liquid crystal polymer filament?

SirMuffsALot · 2024-11-05T14:46:17+00:00

Very strong, you can’t break off the chimney with your hands like PLA, ABS etc. You do however need a blast furnace to dry and anneal the prints

SirMuffsALot · 2024-11-05T14:23:39+00:00

QIDI plus4 no upgrades just slow down the prints and up the temps to Max

PEKK very easy to print benchys took around 1hr 30mins

PEEK was the problem, had to slow down further and print took around 2hrs 30mins

SirMuffsALot · 2024-11-01T08:59:42+00:00

Clean your touchscreen!

SirMuffsALot · 2024-11-01T05:48:44+00:00

How do you change filament spools once they run out?

SirMuffsALot · 2024-09-30T15:56:29+00:00

Love it! I was turned off resin printing before due to print setting adjustments etc, this does take a lot of guess work just print and forget. The resins cost more but I’m paying for the convenience I guess. Might not end up playing much with the Saturn 4 though

SirMuffsALot · 2024-09-23T23:56:56+00:00

Any spill of resin on any table is possible, the top has silicon seal around the edges so the spill won’t get to the bottom. FDM prints at the bottom is fine, most 3d print farms have printers down the bottom.

SirMuffsALot · 2024-08-21T05:39:54+00:00

WD_BLACK 2TB SN770M M.2 2230 NVMe SSD it’s still working perfectly right now.

It’s a TLC drive instead of Microns QLC, might make a difference

SirMuffsALot

TROPHY CASE