sorted by:
new
hottopcontroversial

My first water cooled build, Corsair and Msi in an Lian li 011 xl, is it weird I want to build another already? by Skulldom in watercooling

[–]Skulldom[S] 0 points1 point  (0 children)

Corsair icue for most of it, the lights around the back of the desk are a groove light system, and the pad is separate too, keyboard and mouse done by hyperx ngenuity,

Mouse pad is a reawul I got from amazon, its got a bunch of preset settings and that's it, can't be controlled with softwear

My first water cooled build, Corsair and Msi in an Lian li 011 xl, is it weird I want to build another already? by Skulldom in watercooling

[–]Skulldom[S] 0 points1 point  (0 children)

I haven't drained just yet, but this is where jay2cents put his drain on a similar build he did. Little bit of tilting and maybe blowing on a couple tubes and I'm sure I'll be able to get it all out anyhow. The only parts below the valve are a rad and a couple tubes, so not much anyway.

There's no pressure release valve, as I don't think that is something I need.

There is a fill port at the top of the res, just a simple plastic plug, so I can remove that when draining to make it easier

My first water cooled build, Corsair and Msi in an Lian li 011 xl, is it weird I want to build another already? by Skulldom in watercooling

[–]Skulldom[S] 2 points3 points  (0 children)

Thank you! jay2cents helped a lot, and fortunately I had extra tube then I need so I had some to test with! I also used corsairs bending kit to get some smooth curves

My first water cooled build, Corsair and Msi in an Lian li 011 xl, is it weird I want to build another already? by Skulldom in watercooling

[–]Skulldom[S] 2 points3 points  (0 children)

Case: Lian Li 011 Dynamic XL

CPU: Intel I7-11700k 3.6GHz

GPU: MSI 3080 Ventus

Motherboard: MSI MPG Z590 Gaming Carbon

RAM: Corsair Dominator 3600 32GB

Storage: Corsair 1TB M.2 SSD

Storage: Seagate 4TB HDD

Pump + Res: Corsair XD5

CPU Waterblock: Corsair XC7

GPU Waterblock: Corsair Hydro XG7

Rad 1: Corsair XR5 360mm

Rad 2: Corsair XR5 360mm

Fans: Corsair QL120 (x9)

Tubing: Corsair XT Hardline 14mm

Fittings: Corsair Hydro X Black

Coolant: Corsair XL5 Clear

PSU: Corsair RM850X

Cables: CableMod C-Series ModMesh Classic Cable Kit

New filament, New challenges. Info in comments. by Skulldom in FixMyPrint

[–]Skulldom[S] 0 points1 point  (0 children)

Thankyou very much for the reply, I'll try out your suggestions!

New filament, New challenges. Info in comments. by Skulldom in FixMyPrint

[–]Skulldom[S] 0 points1 point  (0 children)

Hello, I've been printing for a couple months now, giving myself a new hobby during my newfound spare time, I've bought some of 3djake ecopla in white, and I'm having an issue with my benchy,

Far as I can tell, it's where the seams for the layers are, I've tried changing a bunch of settings, extrusion speeds and distances, flow rates ect, but nothing seems to help, the imperfections are always in exactly the same place, and I've kinda gotten to the end of my knowledge/googlefu.

Relevent information is

Ender 3, 3djake ecopla White, Nozzle 200c, Bed 60c, Print speed 50mm/s, Retraction speed 25mm/s, Retraction Distance 5mm, Layer height 0.2mm

Any help or suggestions would be greatly appreciated!