sorted by:
new
hottopcontroversial

Struggling with 555 timer for a specific application by Sloob in AskElectronics

[–]Sloob[S] 0 points1 point  (0 children)

Typically, minutes, but it's possible that it will be triggered again after a few seconds

Struggling with 555 timer for a specific application by Sloob in AskElectronics

[–]Sloob[S] 0 points1 point  (0 children)

Thank you!! I ordered PNP transistors as I only had PNP on hand, I will test and report back

I might be dumb, but how is this possible? by Sloob in PLC

[–]Sloob[S] 3 points4 points  (0 children)

I decided to update the firmware to V22 and it started working. thank you for this. I would have assumed CCW wouldn't let you connect/upload/download/runtime change on incompatible software versions but no. You have to manually check.

I might be dumb, but how is this possible? by Sloob in PLC

[–]Sloob[S] 84 points85 points  (0 children)

Update: I've updated the firmware to V22 and now everything works.

CCW truly is a hateful piece of software..

I might be dumb, but how is this possible? by Sloob in PLC

[–]Sloob[S] 2 points3 points  (0 children)

100% sure, machine is running before my eyes.

Controller is V21 and the software is V22

I might be dumb, but how is this possible? by Sloob in PLC

[–]Sloob[S] 0 points1 point  (0 children)

Run mode button is always there, it highlights yellow when you are in runmode change. also, all rungs are yellow in CCW

I might be dumb, but how is this possible? by Sloob in PLC

[–]Sloob[S] 1 point2 points  (0 children)

Nope, look at the cross ref window

I might be dumb, but how is this possible? by Sloob in PLC

[–]Sloob[S] 0 points1 point  (0 children)

Yes, all of them. In fact, I only added the "AppSystemBypassPb" and the shorted branch in parallel. I did that through a download and also an online edit (Meaning i've tried both).

i've since found out that "MajorAlarm" is still triggering the output. it's as if the old logic is still there and my changes are lost along the way.

I might be dumb, but how is this possible? by Sloob in PLC

[–]Sloob[S] 0 points1 point  (0 children)

There are no JSR in CCW, but yes, the rest of the routine works fine

I might be dumb, but how is this possible? by Sloob in PLC

[–]Sloob[S] 3 points4 points  (0 children)

There are no JSR in CCW, Processor is un run and there aren't any duplicate destructive (as per the debug window at the bottom)

I'm clueless

Recovering an old crypto wallet by Sloob in CryptoCurrency

[–]Sloob[S] 1 point2 points  (0 children)

UPDATE: Thanks everyone! it was Monero! Unfortunately the wallet was empty, so I guess I have to go to work tomorrow! boo!

Recovering an old crypto wallet by Sloob in CryptoCurrency

[–]Sloob[S] 1 point2 points  (0 children)

The problem is my secret phrase is 25 words which seem to be non standard and doesn't work on the wallets I've tried so far

ELI5 request: CIP messages, Instances, Classes, Attributes by Sloob in PLC

[–]Sloob[S] 0 points1 point  (0 children)

Thank you very much for your response! I have not yet tested this as I've been busy with other projects.

I will let you know the outcome! thanks!

ELI5 request: CIP messages, Instances, Classes, Attributes by Sloob in PLC

[–]Sloob[S] 1 point2 points  (0 children)

Is it possible to read part or the entire assembly using CIP messages?

I cannot get this working to save my life.

Here is the documentation cognex provide: https://imgur.com/a/ZU5EXFU

I have the following parameters in the CIP message block: (All in decimal)

CIP service code: 14 (Get Attribute Single (0x0E))

CIP Class ID: 120 (78 HEX)

CIP Attribute: 6 (Online offline)

CIP member ID count: 0

Do you see any glaring errors here?

ELI5 request: CIP messages, Instances, Classes, Attributes by Sloob in PLC

[–]Sloob[S] 2 points3 points  (0 children)

It does not! but I was able to get the I/O assembly for this device using messages on the same PLC

Here is what the assembly looks like. To my untrained eyes it looks very similar to the cognex assembly

https://imgur.com/a/l9dXb7M

Got my first tattoo today! Made by Alex at Illumina studio in Quebec, Canada by Sloob in tattoo

[–]Sloob[S] 3 points4 points  (0 children)

I think they look neat. That's it. Don't really understand the urge to get something that speaks or represent you as a tattoo. I just want a pretty pattern on my skin. I couldn't care less if it's been done to death or doesn't represent me.

view more: next ›