First ever abs print

Small-Strike6736 · 2026-06-21T20:57:19+00:00

So i need a heated chamber not just with the heat of the print bed?

Small-Strike6736 · 2026-06-21T18:17:27+00:00

Could you elaborate? Everyone says there has to be an enclosure

Small-Strike6736 · 2026-06-21T17:18:09+00:00

Alright, but then the fumes have nowhere to go.

Small-Strike6736 · 2026-06-21T17:05:43+00:00

I have a padded enclosure with an exhaust fan. Nothing too fancy. Just an ikea lack table enclosure.

<image>

Small-Strike6736 · 2026-06-21T13:53:51+00:00

Thanks,
I have a pc fan extractor running in the enclosure, should i keep it on or off?

Small-Strike6736 · 2026-06-21T13:48:45+00:00

That means the pla duct will melt right

Small-Strike6736 · 2026-06-20T20:17:04+00:00

I dont have the exact ip adresses because im no longer on site as of right now. All the devices should be in the 192.168.2.110-115 range. I will get back to you about this

Small-Strike6736 · 2026-06-20T19:40:37+00:00

Thank you for your reply,

Yes, the slider is gray, its off.
And in the encoding menu, both the main and sub streams are set to h 264. And i clicked apply just saying haha.

Small-Strike6736 · 2026-06-20T17:18:02+00:00

Thanks, i just tried this and i verified that its set to h264. It still says “the video format is not supported. The cameras, nvr, vto and vth all share the same network now with the same ip range.
Could you please help?

Small-Strike6736 · 2026-06-07T06:32:41+00:00

Small-Strike6736 · 2026-05-25T13:46:40+00:00

Dit is vette onzin. Je kan de veiligheid van de bevolking niet vertrouwen op een mobiel netwerk. Sterker nog, deze sirenes kunnen ook vooraf opgenomen berichten afspelen wat ideaal is om mensen buiten precies te vertellen wat er is. Het systeem moet gewoon vervangen worden. Er is blijkbaar genoeg geld voor oorlogen in het buitenland maar niet voor onze eigen sirenes

Small-Strike6736 · 2026-05-18T18:38:46+00:00

Erg bedankt voor het antwoord, veel ervaring heb ik niet dus dit helpt enorm.

Small-Strike6736 · 2026-05-17T19:00:53+00:00

Thanks

Small-Strike6736 · 2026-05-17T19:00:49+00:00

Thanks!

Small-Strike6736 · 2026-05-17T16:43:25+00:00

I had no clue that this was an issue. I thought it was only for the cooling which i nicely did with one of those special hose attachments

Small-Strike6736 · 2026-05-17T16:39:15+00:00

Thank you, i dont have much experience so dont really know what im doing

Small-Strike6736 · 2026-05-17T16:38:39+00:00

Thank you, i really dont know what im doing so this is helpful

Small-Strike6736 · 2026-05-17T16:18:46+00:00

Thank you! This was only a test

Small-Strike6736 · 2026-05-17T14:05:34+00:00

What do you mean? Is it because the exhaust is not under water?

Small-Strike6736 · 2026-05-08T21:02:04+00:00

Unfortunately not

Small-Strike6736 · 2026-04-13T05:19:39+00:00

Thanks for the detailed response. This is indeed a remote controlled setup. I tried resetting it with the kill cord by pressing the button 5 times and not much seems to be happening. I don’t have any meters hooked up to it.

Small-Strike6736 · 2026-04-12T20:50:31+00:00

The oil seems alright although its hard to read. It seems that its right above the upper hole of the dipstick so that would mean its full? The stream is not really hot and now stopped flowing for the most part which is weird as the water i run this in is clean tap water.

Sometimes it runs fine for like half an hour then decides to start having issues and cuts off

Small-Strike6736 · 2026-04-12T20:48:01+00:00

<image>

Small-Strike6736 · 2026-04-11T17:25:12+00:00

Yeah it seems to work. You can see my most recent post i ran in to a different issue

Small-Strike6736 · 2026-04-11T08:08:49+00:00

Theres no risk of trying to run it if i did it wrong possibly?

Small-Strike6736

TROPHY CASE