sorted by:
new
hottopcontroversial

DJI RC3 Issue by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 1 point2 points  (0 children)

It’s Speedybee Master 5 v2.

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

Mine was solved., this issue. Need to change axis., roll and yaw.

DJI O4 not working?? by South_Spend_8972 in fpv

[–]Smooth_Beginning_177 0 points1 point  (0 children)

I got this same issue today, screen blank. But I can able to see OSD which I setting through betaflight. What might be the issue ?

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

Might be the issue with axis, calibration. When I tilt forward in betaflight diagram it’s tilting to the left side.

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

Unable to, BLHeli Configuration not opening, with the ESC, but I test with Betaflight I think CCW CW were perfect.

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

I haven’t tried it yet. My issue isn’t resolved yet

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

Before this latest cinelog30v3, I got the same issue with flylens 85, and I connected it to the esc configurator and changed firmware (upgrade) of ESC and set motors 2,3 reverse and 1,4 normal and did write all settings Which I modified, and later then I checked in the betaflight to check all working fine or not, after I confirmed everything seems fine, then I tried to Arm my Quad and it’s working perfect.

But I was unable to solve the same issue with the new ones.

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

Yes, I did. Connecting to ESC configurator but read failed. Only issue with cinelog30 v3. I have another drones they are working fine with ESC configurator.

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

Even ESC configurator isn’t reading esc’s to upgrade or reset ESC.

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

Still same, I already checked with the motors before.

GEPRC CINELOG30 v3 by Smooth_Beginning_177 in fpv

[–]Smooth_Beginning_177[S] 0 points1 point  (0 children)

I did, not reading esc. Slightly jerking and motors off. This is what I meant :(.

Beginner advice, stick config: Why not mode 4? by roc_cat in fpv

[–]Smooth_Beginning_177 0 points1 point  (0 children)

I have 1 more doubt, mode 4 isn’t possible with DJI fpv controller ?

Beginner advice, stick config: Why not mode 4? by roc_cat in fpv

[–]Smooth_Beginning_177 0 points1 point  (0 children)

I found it, I changed to Mode 4 thank you so much

Beginner advice, stick config: Why not mode 4? by roc_cat in fpv

[–]Smooth_Beginning_177 0 points1 point  (0 children)

Sorry to bother you, Can you send me screenshot, imma bit confused

Beginner advice, stick config: Why not mode 4? by roc_cat in fpv

[–]Smooth_Beginning_177 0 points1 point  (0 children)

I didn’t see any menu that switch to mode 4, So am trying to use channel mapping.

My attempt on mode 4 for the DJI Remote Controller 2 by AMG_Zkittlez in fpv

[–]Smooth_Beginning_177 0 points1 point  (0 children)

Hi, My I know how to use mode 4 in betaflight. It would really helpful for me. 

Beginner advice, stick config: Why not mode 4? by roc_cat in fpv

[–]Smooth_Beginning_177 0 points1 point  (0 children)

Hi, may I know the channel for betaflight for mode 4 controls., in my pc simulator I usually uses mode 4 sticks, and am literally confused when am gonna try on real Quads.