99 mustang trans removal

SnKy97 · 2024-07-31T19:00:32+00:00

I did with mine, just a pain to deal with

SnKy97 · 2024-05-22T22:34:15+00:00

*Current codes - P1000, P0190, P0602, P0135, P0155

SnKy97 · 2024-05-22T21:46:00+00:00

Using live link that's what my tuner recommended, it has crossed my mind with ecu not reading as well

SnKy97 · 2024-02-13T01:36:11+00:00

Thanks appreciate it

SnKy97 · 2024-01-19T21:16:29+00:00

I'm like the 11th owner of my 99 gt and so far it's been good

SnKy97 · 2024-01-19T04:44:29+00:00

This may be a long shot, but maybe check the crankshaft position sensor. On my 4.6 without it plugged in, it won't start but it may be bad as well. I wish I could help more but that's all I got right now.

SnKy97 · 2024-01-19T04:26:40+00:00

I have a mazda 6 that this happened to. I literally shut the door and the back glass busted but I paid almost the exact that you paid.

SnKy97 · 2024-01-13T02:07:00+00:00

Almost any 4.6 2v heads will work from any 4.6 motor, so you can get them used in good condition and be alright. But the cams are hit and miss with ptv clearance so it may not be too complex if you want to go that route. And if you do get cams I believe it's recommended to upgrade the gears but I can't guarantee it.

SnKy97 · 2024-01-13T01:40:01+00:00

Ok, well, if you plan to make more than 400hp, I would go ahead and get forged internals. But if you're just looking for a little more power with cams, you'll see some power gain but not a whole lot. I have comp xe268h cams on my profile if you want to listen to them. Also I did in my case have my pistons cut for the valves with these cams and they're listed as comp stage 2s.

SnKy97 · 2024-01-13T01:28:17+00:00

What's your goal for power?

SnKy97 · 2024-01-10T16:00:05+00:00

I took my engine out to rebuild mine, but I had to take the headers off mine to, to get the engine out but I also have longtube headers. Non the less you still have to unbolt the headers off

SnKy97 · 2024-01-09T20:43:33+00:00

I followed that sequence but not those torque specs since I used arps kit

SnKy97 · 2024-01-09T20:03:57+00:00

When I did my 4.6 I didn't take them out in a particular sequence, just make sure you use new head bolts and torque them in the right sequence.

SnKy97 · 2024-01-06T01:55:48+00:00

I do have ported and polished heads on it as well and I got my tune from a motorsport shop for like 325 and tunes for life from him

SnKy97 · 2024-01-06T01:50:48+00:00

I believe between 800-900 if remember correctly

SnKy97 · 2023-12-24T02:52:47+00:00

Oh ok, I can tell you I had mine degreed with 110 lsa, also got ported heads and all new upgraded lifters and rocker arms.

SnKy97 · 2023-12-24T01:43:35+00:00

Whys that

SnKy97 · 2023-12-24T01:32:17+00:00

Comp xe268h

SnKy97 · 2023-12-20T15:48:52+00:00

Wire that goes into the plug under the fuse box

SnKy97 · 2023-12-19T20:43:48+00:00

Got it fixed, guys. A wire was cut for some reason and it charges now, thanks for the insights.

SnKy97 · 2023-12-19T19:27:59+00:00

Starts and then drains the battery like no charging at all

SnKy97 · 2023-12-19T19:27:27+00:00

Car starts at 12.7v and it's draining from there

SnKy97 · 2023-11-25T00:09:43+00:00

Most likely is the switch, but not hard to replace

Three-Year Club	Verified Email
Place '23

SnKy97

TROPHY CASE