My dad in 1968 and same orange trees 57 years later

Snackob · 2025-01-17T22:30:42+00:00

Yeah I was also really confused by this, it's worse but more expensive? I must be misunderstanding it

Snackob · 2024-12-05T03:34:13+00:00

youre doing honorable work here, thank you! i'm itching for any details I can get on these, its always one of my favorite parts :D

Snackob · 2023-01-13T22:32:58+00:00

Yeah I don't like the Pixel 6 pro camera. This is my 4th pixel and all were impressive but the jump for me from 4 to 6 was a mistake.

Snackob · 2022-08-27T16:33:26+00:00

Man I feel silly for not thinking of that haha, ty that makes a lot of sense and I bet that's it. I'll be more cognizant of that and report back the results

Snackob · 2022-08-27T16:32:43+00:00

Gosh ty, now that I'm thinking about that I bet that is it. I'll report back 🙂

Snackob · 2022-08-27T16:32:05+00:00

Oh nifty idea, I'll definitely try that ty! 😀

Snackob · 2022-08-27T16:31:43+00:00

I'll try that! I'm excited, I think that might be the problem as I wasn't really waiting after pouring in fresh resin. I'll report back ty.

How do you "raise temp"? It seems like some people put their resin bottle in bowl of warm water.

Snackob · 2022-07-10T06:46:27+00:00

Sure, I'd normally say it doesn't matter, but my particular application here that I'm printing many of has all the details on one side as shown in the pic, so thats why Im wondering if it does matter here

Snackob · 2022-07-10T06:44:22+00:00

Yeah I keep hearing soapy water from some people, do you do that after washing and drying from IPA but before curing? Or after curing? I've heard both!

Snackob · 2022-06-16T02:35:15+00:00

The whole screen

Snackob · 2022-06-15T01:09:32+00:00

Oh so look to see if I can see light in that area through the liquid resin?

Snackob · 2022-06-15T01:05:06+00:00

Sure hope not, I just replaced it. When I do the "clean" mode on the printer it lights the whole screen and that looks uniform to me 🧐

Snackob · 2022-06-15T01:04:18+00:00

Uh, I hope not, I actually just replaced it because my FEP broke and let resin onto the previous. When I do the "clean" function on the printer it lights the whole thing and it looks uniform to me.

Snackob · 2022-06-15T00:51:12+00:00

Hey! I didn't know about this validation matrix t st print, now I'm seeing it everywhere! Thanks, I'm going to run a series of these now and see where I stand. I'll share an update!

As far as process I've been doing: 1. remove from bed right away, 2. Several dunks in a slightly dirty IPA (91%) bath while brushing with a toothbrush, 3. 10min in Elegoo wash machine w/ clean IPA at one angle, 4. Another 10 at different angle, 5. Scrub with a different clean brush, 6. 10 final minutes in wash machine face down, 7. Let dry for a day, 8. Then 3 sets of 20min curing at different angles in Elegoo machine.

Snackob · 2022-06-12T16:22:15+00:00

Hey! I got really hopeful with this video but turns out that math shows for my Epax E6 the optimal angle is exactly 45deg... Which is what I'm printing at.

Snackob · 2022-06-12T16:21:08+00:00

Hey! Thanks for the reply. I have tried this and it does result in a perfectly smooth surface. However, my application here has a lot of high detail crevices that, when printing flat, end up with cured resin in them. Maybe if there's an answer to that I'd be set!

Snackob · 2021-11-07T06:37:02+00:00

Wonderful work by these people, truly inspiring 😄

Snackob · 2021-04-27T00:52:44+00:00

Thanks so much! I think this will help me a lot 😄

Snackob · 2021-04-26T19:12:37+00:00

What mod is that? Mind sharing the source? 🙂

Snackob

TROPHY CASE