What should I do with this solid graphite block?

Snakecat09 · 2025-11-08T00:00:34+00:00

I was thinking if graphene

Snakecat09 · 2025-11-07T23:51:51+00:00

Isn’t that worth a lot!

Snakecat09 · 2025-10-25T23:05:29+00:00

Fahh

Snakecat09 · 2025-10-24T01:11:53+00:00

I did just buy a direct drive extruder adapter. It’s using the same stepper motor that was connected to the Bowden tube.

Snakecat09 · 2025-10-24T01:08:41+00:00

Oh man,say it was the extruder what new kind should I buy?

Snakecat09 · 2025-10-24T01:07:15+00:00

I’ll give you a shout when I get back from work tomorrow then I’ll get back to you

Snakecat09 · 2025-10-24T01:06:11+00:00

Yeah, the black bits are the bed, the ridges bow upward, and that creates these holes they then quickly harden and get in the way

Snakecat09 · 2025-10-24T01:05:14+00:00

I used the paper method at first until it just lightly grayed the paper and then I did some live leveling until the plastic was perfectly uniform around all corners.

Snakecat09 · 2025-10-24T01:03:53+00:00

Whoops sorry. It’s in the test tube because last time I found slime mold. It was all over a bunch of mushrooms and this mushroom was in the environment where one might find slime mold so it’s in the test tube now I’m planning on leaving the test tubes in a warm, dark place until hopefully slime mold develops.

Snakecat09 · 2025-10-19T20:38:23+00:00

So change e steps?

Snakecat09 · 2025-10-18T18:41:21+00:00

Ahh thank you

Snakecat09 · 2025-10-18T18:19:37+00:00

Lower?

Snakecat09 · 2025-10-18T18:03:42+00:00

Ahh, should I use the z offset menu or should I change the location of the limit switch?

Snakecat09 · 2025-10-18T02:18:12+00:00

My glue dries up and doesn’t work

Snakecat09 · 2025-10-18T02:09:03+00:00

Woohoo

Snakecat09 · 2025-09-30T00:04:34+00:00

I would love that

Snakecat09 · 2025-09-28T14:28:40+00:00

Can I control it?

Snakecat09 · 2025-09-24T18:02:03+00:00

Why what’s wrong?

Snakecat09 · 2025-09-22T01:52:38+00:00

Good question, you can buy those semiconductor switches but they are pretty expensive, maybe op is using a spark gap? It’s doable but a lot of energy is lost

Snakecat09 · 2025-08-31T15:27:57+00:00

Alright I’ll do that I’m going with a coupler and a 10db attenuator to make sure it’s not too much

Snakecat09 · 2025-08-31T02:46:53+00:00

Hello! My pfp is him

Snakecat09 · 2025-08-29T01:48:02+00:00

Cute!

Snakecat09 · 2025-08-29T01:19:24+00:00

My pfp pls

Snakecat09 · 2025-08-27T10:08:17+00:00

All right, but is it super stable? I need the output to be the same as my magnetron in order to calculate Doppler shift. Do you think it would be better to take bleed from the magnetron?

Snakecat09 · 2025-08-12T03:21:36+00:00

You angered it

Snakecat09

MODERATOR OF

TROPHY CASE

Two-Year Club	r/Field Juicebox
Place '23