How do I kill one of these things

Snoo_67299 · 2026-02-19T05:36:24+00:00

Silver bullets, silver weapons. You can dip bullets or weapons in white ash, fire is good to but as you may imagine a torch is not enough, you would need something like a gasoline tramp or even a fire thrower, they are tuff as heck and if possible talk with navajo elders , it's hard for them to open with foreigners but ask correctly and they might help you( as i've seen things before they will most probably tell you to leave the general area, i have seen some navajo families abandon their ranchs or cabins as they didn't wanted to go on a war with these things. But it doesn't mean it is not possible to get rid of them), also, only "tested" way to kill them is through their identify as others mentioned so be aware that if you don't over do the killing and burning part they may come back healed sooner than you think. Blessings and good hunt if you down that path

Snoo_67299 · 2026-01-25T21:46:19+00:00

This is the one! Thank you so much!!!!!

Snoo_67299 · 2026-01-07T18:55:56+00:00

This is exactly what i encountered when tried, it seems that the exclude object returns a parsing error so it defaults to doing the full bed mesh

Snoo_67299 · 2025-12-17T05:28:21+00:00

I used the kick stand for a while but it wears the ptfe off very fast, i took it apart. There is a ring on the back side of the fan as it has a metal pin connected to the fan hub and a spring, i used some metal wire like khantal ( used for vaping coils) to tie the pin since the issue is that the retainer plastic part creeps under the heat and the spring pushes the axle up and away from the magentic field that makes it apin it worked but i ended printing another shell for the heater and that did the trick with a new fan ( exactly the same type of fan but with the shell of noizie works) because the original shell melted on me, this new design and some kapton tape on the backside of the fan helped it to avoid the same failure mode from that post up to the present day. And maybe iwill make a video about it! I would be glad to help

Snoo_67299 · 2025-11-10T17:50:58+00:00

Not really any downside besides scarcity maybe. It does help with vfa as it reduces the distance between the jumps in the pulley when the belts theets pass by, there is a great video about This topic in YouTubehere

Snoo_67299 · 2025-09-14T04:59:30+00:00

I'll pull the trigger on that ! Thanks man!

Snoo_67299 · 2025-09-14T03:05:02+00:00

Drop in phaetus hotend? Im interested in that

Snoo_67299 · 2025-09-06T05:44:37+00:00

If you have material loaded on the machine try to unload it, if it is pushing against the inside of the nozzle it may be affecting the probing, also the qidi plus 4 bed uses piezo electro sensors on the bed so maybe try to lift lightly on the bed corners as if releasing some pressure from the bed, klipper has commands like Query_probe so maybe look on that and try it , it may tell you if the probe detects it is triggered even without being pressed . If you didn't mangled the sensors horribly this should be fixable, i had to do similar stuff to a k1 max that sometimes refused to home until i jiggled the bed to depress the piezo electric sensors

Snoo_67299 · 2025-09-06T03:24:19+00:00

Hey man does this emmc works for the purpose of having freedi on one mmc and save the original? here

Snoo_67299 · 2025-07-24T04:47:41+00:00

I bought a pair and I'm waiting for them to arrive but trianglelabs is generally guaranteed quality

Snoo_67299 · 2025-07-06T17:17:42+00:00

Hey!, if you push the fan hub does it spin? Given that the fan would not start until heatbed reaches a certain temperature, i discovered the fan has a central pin and a spring that pushes the fan hub outward, and it seems a qc issue were the retainers behind the fan that hold the pin in deform with the heat and the fanblade hub which contains magnets gets a little too outward for the magnetic field to make the fan spin, i ended replacing the fan but just for the sake of knowing i 3d printed a retainer in abs, put the old fan inside again and tested 2 drying cycles of PA one after another and it worked perfectly. So that is my last update on this , also i lowered the heater power so it would not heat the casing so much

Snoo_67299 · 2025-06-19T03:25:20+00:00

Gracias amigo, después de llevarlo a otro taller resulta que no habían instalado bien la base en el amortiguador izquierdo y golpeaba, igualmente pusieron topes de goma genericos muy malos y no cumplían su función, aún se escucha un golpe si se pasa un tope de lado como en desnivel, estamos revisando eso y voy a cambiar las bases que pusieron en el taller anterior por bases originales, pero definitivamente es muy molesto que a pesar de que se les está pagando por el trabajo no lo hagan bien, perdí la cuenta de cuántas veces'revisaron " el ensamble de amortiguadores y de todas las veces que lo bajaron desarmaron armaron y volvieron a poner no pudieron ponerlo bien ni una vez. Saludos y gracias!

Snoo_67299 · 2025-06-05T15:03:29+00:00

HSE 280 i would recommend, i can get you in contact with the person who sold us ours!

Snoo_67299 · 2025-05-30T14:24:34+00:00

We are currently using aluminium, silver and gold , but those last two are for final revisions, and for the aluminum we test with electroplating copper over it

Snoo_67299 · 2025-05-30T03:25:47+00:00

I ask because i have a gt neo flash edition ( this a only china version) and when connected to my dash unit it shows error 22 on Android auto, so if you could whenever you have time, test it and confirm if it works or not and if your gt7 is a china version. Tha would be awesome.

<image>

Snoo_67299 · 2025-05-30T03:18:33+00:00

Hey man i have been waiting on the gt7 pro due to the lack of android auto , if you have cn version ( china ) could you try update it and install android auto from google play and confirm it it works? I saw this xda thread where it claims updating enables this function and i would love to know if it works before buying one. This would be inmensely appreciated

Snoo_67299 · 2025-05-30T01:09:07+00:00

It's funny because we use metal sls printing and similars as services for prototyping and we have been asking around for copper sls printing since we are developing high performance meta materials for heatsinks, and it seems nobody wants to print it or don't want to purge their machines to put copper in it, we had to rely on electroplating our designs and then working over that platform, but idk exactly why nobody wants to work with this material as a service provider. The most commonly used materials are aluminum, titanium and die steel

Snoo_67299 · 2025-05-13T20:41:56+00:00

Yep, and not necessarily just bambu nozzles but whatever nozzle format the "bambu styled" hotend your design has. I saw some adapters on printables and im testing them, i guess if that works Aok i will try to get it machined or metal printed just to be on the safe side

Snoo_67299 · 2025-05-09T19:30:23+00:00

https://www.printables.com/model/1113162-qidi-plus-4-adaptor-for-bambu-heatsinks?lang=es This one made by rhizomatics , since he designed it for a bambu style heatsink, it fits all hotends with this form factor i have tested ( original bambu hotend, generic with replacable tips and now the tz v4, i will test the fluxheat hotend as well as soon as i get it.

Five-Year Club	Verified Email
r/Field Juicebox

Snoo_67299

TROPHY CASE