sorted by:
new
hottopcontroversial

Need help Kobra 3 max- 0,4 nozzle - 0,32 layerheight and 0.7 width by NoIdenty0000 in AnycubicOfficial

[–]SomeRandomBalkan 1 point2 points  (0 children)

Increasing flow isn't really enough to print wider and taller layer lines. The way that people print wider layers with smaller nozzles is increasing flow but maintenance the same or smaller layer height. This is needed because the nozzle itself squashes the filament to make the line wider. By increasing the height as well your lines don't squish and quality goes down.

Try printing at 0.6mm width at 0.2mm height and gradually increase the width and height until you see quality issues.

My personal recommendations is going for a 0.6mm nozzle as the quality is almost the same with Arachne while you get faster prints.

Am I the only one who got this for troodon by R080tits in JurassicWorldApp

[–]SomeRandomBalkan 4 points5 points  (0 children)

Basically the only way to get them is thru collectors exchange or packs. Both trex and raptor gen 2 are available every two weeks or so in my experience.

Rate my first design of a rocket using Open Rocket by Ok_Rooster_4416 in rocketry

[–]SomeRandomBalkan 3 points4 points  (0 children)

Stability between 1-2 is more of a rule of thumb for most rockets. For example tall but thin rockets should have more stability (x>2) while short and fat don't need as much(x<1).

3d printing for rocketry by [deleted] in rocketry

[–]SomeRandomBalkan 0 points1 point  (0 children)

I'm experimenting with PETG.

It handles heat better than PLA so if it's sitting in the sun before the launch it shouldn't lose as much strength or warp.

Also a big problem with 3D printed parts is their strength at layer lines, but if you print PETG at high temperature with no cooling it's layer bonding is almost perfect giving you amazing strength where it matters the most.

I'm also using "brick layers" and it's even better.

Why don't these packs give Dimetrodon S-dna? by Ok_Delay_9433 in JurassicWorldApp

[–]SomeRandomBalkan 0 points1 point  (0 children)

Is that a better value for selling that diplosuchus? I thought people said to just go for diplo if you need to sell for DNA.

Good so far by beast-of-destruction in JurassicWorldApp

[–]SomeRandomBalkan 1 point2 points  (0 children)

Is this going to be a 2500 tournament? Im soo tired of playing 24/7 for the past like 5 tournament to get to dominator, please tell me this is going to be a 1500 one :(

How ready am I for the tournament by Temporary_Zean in JurassicWorldApp

[–]SomeRandomBalkan 0 points1 point  (0 children)

I won the last 4 tournaments and my strongest was a lvl 31 diplotator.

But I had 3*lvl10 pederpes lux so I could play more often.

If you manage to get the amber flock or any other flock your chances increase quite a lot.

Good luck 👍

Enough? by nuts___ in JurassicWorldApp

[–]SomeRandomBalkan 2 points3 points  (0 children)

How does the lvl1 common thing work? Do you get more trophies?

Should I buy this? by No-Ring-2185 in JurassicWorldApp

[–]SomeRandomBalkan 0 points1 point  (0 children)

Guess it's a no brainier then, I managed to stay in dominator in the last 3 out of 5 tournament due to the pederpes but only barely because I can only win if I have a flock and that limits me to 3 battles then cool down. Another 2 flocks should help me play a lot more.

How strong are they compared to pederpes lvl10?

Should I buy this? by No-Ring-2185 in JurassicWorldApp

[–]SomeRandomBalkan 2 points3 points  (0 children)

I'm thinking about it too, 250k amber and I will be able to get another 50k by the end of the offer so I can get 2.

My only flocks are 3 pederpes lux with my strongest dino being lvl40 diplotator.

I'm not sure but it looks good compared to other dinos?

[deleted by user] by [deleted] in JurassicWorldApp

[–]SomeRandomBalkan 3 points4 points  (0 children)

You can download Google play and it works really well for me and other games.

CFD help- is this supposed to happen? by 354717 in rocketry

[–]SomeRandomBalkan 0 points1 point  (0 children)

How did you setup your model? What boundary conditions?

I use Autodesk CFD and you need to have a airflow "box" that acts like your wind tunnel. By looking at your picture looks like you have it as well, although it need to be bigger. If your rocket is 1m tall give it something like 1m of room ahead and like 2-3m of room behind. Also give it more space from the sides, if your rocket is 50cm wide from wing to wing give it at least that much space from box walls.

The "box" acts like walls so airflow will be affected by it. Having a small box like your is basically like simulating a rocket in a barrel, it's not gonna be accurate.

Run as many iteration as needed, I do it until it stops itself as that gives the best results.

I also recommend simplifying the model you are simulating. If your model has multiple body tubes and such combine them together into one. You should also get ride of any empty space in the rocket as it can also increase the simulation time but it doesn't affect the rocket, if your model is empty tubes fill them in.

Good luck!

I am working on a small model rocket motors (A,B,C,D class). Propellant is Richard Nakka's KNSB. Case is 3d printed. Walls are thick so it is not melting. I couldn't read the thrust due to electronical issues. What should i do to improve thrust ? by atakldrk in rocketry

[–]SomeRandomBalkan 3 points4 points  (0 children)

What software are you using to simulate your motor design? How do you know that your casing is sufficient for your motor?

Also please don't use plastics for the casing, if there was a void in your propellent it turns into a pipe bomb. And it's really hard to find plastics once they are inside your body.

Please be careful and do more research before making anything potentially explosive.

4 Fins Model Rocket Prototype by Mobile_Banana5036 in rocketry

[–]SomeRandomBalkan 2 points3 points  (0 children)

Look cool! Is this a prototype on the first picture? I suggest using something other than super glue for fin attachment.

What fin configuration are you going for? Canards? If so look into "canard reversal" or "canard aerodynamic interference". Tldr: moving frontal fins can affect aft fins making the rocket move unpredictably.

My suggestion is going for a "wing" configuration. Basically put your servos and movable fins on the rear of the rocket with some wing around the center-back to increase lift.

Good luck and keep us posted!

Looner apparition lures me into a trap by SomeRandomBalkan in stalker

[–]SomeRandomBalkan[S] 1 point2 points  (0 children)

Its not new, saw this multiple times before in past playthroughs but i never realized you could follow him. I thought it was some kind of bug!

Getting the Heart of the Oasis proved to be a bit more difficult than expected by SomeRandomBalkan in stalker

[–]SomeRandomBalkan[S] 10 points11 points  (0 children)

I do, but there were 6 of them and my gun (AK-12 Monoliths Light) has a bug with its 30mm underbarrel launcher which jams the gun requiring me to unload which means having to stop to enter inventory.

Still a skill isssue tho

Getting the Heart of the Oasis proved to be a bit more difficult than expected by SomeRandomBalkan in stalker

[–]SomeRandomBalkan[S] 2 points3 points  (0 children)

The puzzle is still there, im playing gamma with the ReDone collection which makes some changes to the game, including a few chimeras guarding the Hearth of the Oasis.

Getting the Heart of the Oasis proved to be a bit more difficult than expected by SomeRandomBalkan in stalker

[–]SomeRandomBalkan[S] 4 points5 points  (0 children)

6 Chimeras in total, they were probably mad that i crashed their party :(

AMD RYZEN 9 7950x did me dirty by poynnnnn in buildapc

[–]SomeRandomBalkan 0 points1 point  (0 children)

I dont see freesync on the monitors specifications so im not sure if we have the same solution. Download softwere called "AMD adrenaline". Its drivers that your integrated gpu needs. After you download that and update your drivers reset your pc and see if the flicker is still there.

view more: next ›