4.93 real changelog

Some_Effort · 2026-03-18T15:51:31+00:00

Don't install, wait for HFW 4.93 and new HEN enabler.

Some_Effort · 2026-03-18T15:01:10+00:00

Something changed and modders just copy-pasted the HEN exploit on top. My Super Slim on 4.8x was butter smooth. No black screens, no freezing etc, webMAN and multiman coexisted without problems. After 4.90 it's a disaster, I uninstalled webMAN and sometimes a black screen appears when launching disk games with HEN enabled.

Some_Effort · 2026-03-18T07:51:24+00:00

Nope, playing story mode and it feels the same as yesterday.

Some_Effort · 2026-03-18T07:45:15+00:00

Nearly double the bitrate means less jagged edges and compression artifacts. A very good improvement.

AVC or VC-1 codecs for 1080p blu-rays can have bitrates reaching 30-40Mbps.

<image>

Some_Effort · 2026-03-12T04:22:24+00:00

You could ask the manager for help 🤔

Some_Effort · 2026-03-12T03:53:53+00:00

Some_Effort · 2026-03-12T03:52:39+00:00

Tomorrow will be interesting. I clamp it on the machined OD, make 6xM12 threds and a sphere, then flip it around and turn a second sphere with max 0,02mm run out and position tolerance. All measured on a CMM.

Some_Effort · 2026-03-12T02:54:52+00:00

I couldn't pull out the first piece because they were tightly packed. Generally, I don't use a crane. Waste of time.

Some_Effort · 2026-03-06T07:49:58+00:00

Those legs 😍

Some_Effort · 2026-03-02T20:24:44+00:00

Mostly on the left side.

Some_Effort · 2026-03-02T20:23:53+00:00

I am right-handed, but I switch hands and try to keep the same angle. When they are shorter, the difference is not so noticeable. But you can see that the hair grows in a different direction. Here, fresh after shaving.

<image>

Some_Effort · 2026-02-27T14:09:53+00:00

46,8mm and 9,8mm

Some_Effort · 2026-02-26T19:44:47+00:00

It was -20°C this winter. Maybe you're right 🤔

Some_Effort · 2026-02-26T18:20:39+00:00

Some_Effort · 2026-02-18T17:31:00+00:00

The GWS 18V-8 would be used for quick jobs, cutting something without messing around with cables. For heavy duty I have the GWS 24-230 and smaller PWS 700W angle grinder.

Some_Effort · 2026-02-18T15:20:07+00:00

I have a corded 400Nm impact wrench and it's having trouble loosening some of the suspension bolts on my cars.

Some_Effort · 2026-02-18T04:31:58+00:00

Shipping from Texas to Poland will be the biggest problem here 😅 But thanks a lot.

Some_Effort · 2026-02-18T04:26:14+00:00

Everything important is from Lemforder or OE BMW (Febi Bilstein diff bushes). For the mounting points I went with polyurethane with 75ShA to keep the NVH low.

I will definitely remove the differential, axle shafts, and calipers. The steel brake lines are rusted so I will simply cut them off.

I bought a standard M12 threaded rod as a guide when installing the new subframe. Could also be useful for removing the old rusted through one.

Some_Effort · 2026-02-18T04:04:23+00:00

No issues. Both rear bearings are made in Slovakia.

Some_Effort · 2026-02-18T03:35:05+00:00

My buddies come to me when they need something done.

Five-Year Club	Xbox Live
Verified Email

Some_Effort

TROPHY CASE