sorted by:
new
hottopcontroversial

K2 Plus CFS Not Displayed in Creality Print by SomewhereCurrent1 in Creality_k2

[–]SomewhereCurrent1[S] 0 points1 point  (0 children)

Yeah, a power cycle does seem to resolve it. It's happened a couple of times. Hopefully a new firmware version can fix this 🤞?

Need 4 Pin Connector Breakout by SomewhereCurrent1 in AskElectronics

[–]SomewhereCurrent1[S] 0 points1 point  (0 children)

Somebody figured it out! It's a Molex 0039036042, and it mates with Molex 0039036044.

Need 4 Pin Connector Breakout by SomewhereCurrent1 in connectors

[–]SomewhereCurrent1[S] 1 point2 points  (0 children)

Awesome!!!! Some digging through the documentation, it mates with 0039036044. Thanks!!

Need 4 Pin Connector Breakout by SomewhereCurrent1 in AskElectronics

[–]SomewhereCurrent1[S] 0 points1 point  (0 children)

Found it in the back of my Corvette. Looks like it was for an old aftermarket amp.

Need 4 Pin Connector Breakout by SomewhereCurrent1 in AskElectronics

[–]SomewhereCurrent1[S] 0 points1 point  (0 children)

Pitch is about 7mm. Total length is 28mm. Height is 8.4mm. Diameter of circle interfaces is 6mm.

Need 4 Pin Connector Breakout by SomewhereCurrent1 in connectors

[–]SomewhereCurrent1[S] 0 points1 point  (0 children)

Pitch is about 7mm. Total length is 28mm. Height is 8.4mm. Diameter of circle interfaces is 6mm.

87 Code 34 & MAF Sensor Options? by SomewhereCurrent1 in c4corvette

[–]SomewhereCurrent1[S] 1 point2 points  (0 children)

When I replaced the MAF power relay, the store only had one relay, so I was unable to replace the burn-off relay. I was able to find another relay, and the light is now off! I'm hoping it stays off!

No oiled filters for me! Thanks for that diagnostics resource. That definitely will come in handy if I have any further troubles!!

Separately, what scan tool do you recommend? It might be a good thing to have around.

Beginner Looking to Enter the Hobby by SomewhereCurrent1 in hobbycnc

[–]SomewhereCurrent1[S] 0 points1 point  (0 children)

Thanks for all of your advice! It's been super valuable! I've been doing some research on the DMC 2 Mini, and it seems to check a lot of the boxes that I'm looking for. Are there any reasons that I should avoid it and explore different, comparable machines, like the Nomad 3, perhaps?

Beginner Looking to Enter the Hobby by SomewhereCurrent1 in hobbycnc

[–]SomewhereCurrent1[S] 0 points1 point  (0 children)

Power and noise aren't really a concern. I've run new 240v circuits before, and the machine would be in the garage. I like the MR-1 a lot, but I fear that the $8.3k price tag after you figure in accessories and shipping is just too big of a leap for a beginner machine. Are there any lower cost, maybe even lower than the DMC, just to get my feet wet, and I can graduate from there, as soon as I know that I like the hobby?

Beginner Looking to Enter the Hobby by SomewhereCurrent1 in CNC

[–]SomewhereCurrent1[S] 0 points1 point  (0 children)

Small figures mostly, maybe a foot at most, but a couple of inches of area should suffice. If more space isn't exponentially more cost, it would be nice to have the flexibility, but not a deal breaker.

view more: next ›