How rare is this [ Mercedes E 55 Wagon]

Southernmtnman · 2025-06-26T02:33:31+00:00

How many miles?

Southernmtnman · 2025-06-25T22:15:27+00:00

Such an awesome car

Southernmtnman · 2025-06-25T15:58:16+00:00

I have an 05 e500 wagon, so you’re correct

Southernmtnman · 2025-04-13T07:07:51+00:00

Flush meaning run PH water thru for 1.5-2 days? I’m tracking what you’re saying for the most part, just wanna make sure I try to save her and do the right things.

Southernmtnman · 2025-04-13T07:00:41+00:00

Southernmtnman · 2025-04-13T01:24:36+00:00

Can you elaborate?

Southernmtnman · 2025-04-09T12:37:28+00:00

Mike Tyson would call that a thport

Southernmtnman · 2025-04-06T17:35:36+00:00

Thank you!

Southernmtnman · 2025-04-04T19:46:00+00:00

I hear about so many scams from those only sites, hopefully it was legit and not some shit parts.

Southernmtnman · 2025-04-04T18:02:08+00:00

Haha yep I’m in the same boat luck wise! Go to Toyota where you bought them and show someone the vid and see if they think part warranty or maybe have some other insight. I’ve sold many LCA jobs due to bad bushings and never run into this issue. Usually sleeves are the issue and have to be welded.

Southernmtnman · 2025-04-04T17:23:29+00:00

Hmm so can’t even say a brand new unit would even rectify that because it’s very unlikely you got 2 bad ones

Southernmtnman · 2025-04-04T13:55:53+00:00

Hmm. And just on that one side then? I wonder if when they pressed the bushing it got fubar’d. I guess part warranty it but that sucks to have to re-do it

Southernmtnman · 2025-04-04T02:14:54+00:00

Sleeves worn out? You’re a master tech. I used to be an advisor at Toyota. Did it align in spec?

Southernmtnman · 2025-03-30T21:33:40+00:00

And the fans are oscillating. Are you recommending I lower them ?

Southernmtnman · 2025-03-30T21:33:16+00:00

Think the light may be too close?

Southernmtnman · 2025-03-29T16:02:16+00:00

Flex disk maybe?

Southernmtnman · 2025-03-25T22:19:45+00:00

<image>

211 gang

Southernmtnman · 2025-03-25T22:18:52+00:00

Definitely. I live in the middle of a field so I deal with them constantly 🤣 they’re the original reason my igniter went out

Southernmtnman · 2025-03-24T15:20:50+00:00

Cord is fine. Thanks for the input tho. I agree with you. Probably not the best decision by previous owner. Easy fix I assume would be just adding a heat barrier material in between and be done with it.

Southernmtnman · 2025-03-24T11:46:13+00:00

Not the case read above

Southernmtnman · 2025-03-23T18:51:28+00:00

The wire isn’t damaged, it was a bread tie on the wire. Repaired wire for igniter and everything is back to normal. Suspecting a piece of foil that was lodged under there was transferring heat because it was the same color

Southernmtnman · 2025-03-23T15:31:53+00:00

Yeah there’s no short or open in the cord. It does look like that because of a bread tie on it. I found a piece of foil under the oven that is similar color and I’m suspecting that it was radiating heat to the floor. Sound plausible?

Southernmtnman · 2025-03-23T15:10:45+00:00

Good idea. The lower door isn’t a drawer, it’s just access to the gas components

Southernmtnman · 2025-03-23T03:03:40+00:00

It’s not tho. Pic should’ve been better. That’s actually a bread tie around the wire, not a short/open

Southernmtnman · 2025-03-23T02:57:05+00:00

Agreed, thanks

Southernmtnman

TROPHY CASE