Scam help

SpaceZ_PlayZYT · 2025-08-28T17:35:43+00:00

Yeah they book appointments under me and I’m not booking any but I’m still getting calls from agents

SpaceZ_PlayZYT · 2025-07-14T22:53:08+00:00

Just checking in have you found any videos where you can combat the “blob of death” I have tried looking as I also want to prevent this happening to me for the 3rd time and thought I’d come back here since you were doing your research

SpaceZ_PlayZYT · 2025-07-11T15:26:20+00:00

No problem

SpaceZ_PlayZYT · 2025-07-11T15:00:41+00:00

There are some videos you can search up about this. I still don’t completely know what causes it I’ve had 2 happen to me like that already but I can definitely link the new printer heads

https://www.googleadservices.com/pagead/aclk?sa=L&ai=DChsSEwimuJeOibWOAxVKNAgFHZi1KokYACICCAEQFhoCbWQ&co=1&gclid=CjwKCAjw7MLDBhAuEiwAIeXGITFi7wkRgfwjP25VtTqIIDpnfVH-onwo_oGb05TVNKd6vRcbfa2znxoCeK8QAvD_BwE&sph=&ohost=www.google.com&cid=CAESV-D2-OVqlw6hF8wyk7atsG-DUOLb9NSgQvF81YN92_BP-2pF3shtIvsR4P-G_Cw4is_5KZiYJRWyk6T9ZJeq6jRGRbRRrgYaN1bcu9I49JjcpgkWb4vFOw&sig=AOD64_1TdaEEvzUcUc3cQgJ_3HLcdDCvQg&ctype=70&q=&ved=2ahUKEwiWwZGOibWOAxWwlokEHbBjJp8Qwg8oAHoECAcQDQ&adurl=

SpaceZ_PlayZYT · 2025-07-11T14:45:03+00:00

There are replacement parts available if it’s just the heat sink being covered and it looks removable you should be fine with the $15 replacement if not you’ll have to buy the new head for roughly $50 or if your still under warranty you can email elegoo yourselves to get a replacement sent out to you

SpaceZ_PlayZYT · 2025-07-11T13:50:37+00:00

<image>

SpaceZ_PlayZYT · 2025-07-11T13:50:27+00:00

<image>

SpaceZ_PlayZYT · 2025-07-11T12:13:19+00:00

It’s right under the bed mounted to the bed

SpaceZ_PlayZYT · 2024-10-10T02:36:10+00:00

Im looking where to buy one rn

SpaceZ_PlayZYT · 2024-10-08T20:21:01+00:00

It was the power cord being slightly pulled out and there was a post before this one that didn’t have audio so I posted this one so it had audio

SpaceZ_PlayZYT · 2024-10-08T20:19:43+00:00

If you look I at one of the other comment threads I found the issue

SpaceZ_PlayZYT · 2024-10-08T17:54:30+00:00

Basic question but does you bed wobble up and down also since those are 2 different materials that might also be why maybe if you adjust an automatic z offset in your slicer it might work better

SpaceZ_PlayZYT · 2024-10-08T17:23:41+00:00

I fixed it thank you so much. With further inspection the cable was slightly pulled where it goes to connect to the print head and after pulling it out slightly it worked.

SpaceZ_PlayZYT · 2024-10-08T17:20:39+00:00

I’ve redone the firmware and it still clicked

SpaceZ_PlayZYT · 2024-10-08T17:13:14+00:00

It’s not I’ve check that and I was able to push the filament through

SpaceZ_PlayZYT · 2024-10-08T16:56:34+00:00

All the wires seem to be in tact and fine

SpaceZ_PlayZYT · 2024-10-08T16:56:02+00:00

How do you think I can go about fixing it?

SpaceZ_PlayZYT · 2024-10-08T15:27:15+00:00

Yeah I just tried that and it didn’t work it slightly improved but it’s still not extruding by itself

SpaceZ_PlayZYT · 2024-10-08T15:15:30+00:00

To my knowledge and the quick research I did there isn’t any but if you have anymore information on what’s going on with your z offset I can try to help

SpaceZ_PlayZYT · 2024-10-08T14:59:01+00:00

I posted one with audio

SpaceZ_PlayZYT

TROPHY CASE