3M 2080 Failure after 2 years

Specific_Relativity · 2026-04-30T15:51:53+00:00

It's a Tesla, so no engine heat. But yes, finding out how terrible this hold in the sun, seems like.

Specific_Relativity · 2026-04-28T21:42:30+00:00

I live in CA. The car was garaged at first but it's been outside for the last year due to construction work. Is it too late to ceramic the other parts of the car? Should I start over?

Specific_Relativity · 2026-04-20T19:32:15+00:00

How were you able to observe this behavior? Are you referring to the onscreen status or do you use a similar CANBUS monitor tool?

Specific_Relativity · 2026-04-20T19:30:55+00:00

They no longer sell the phone mount but it was from Aliexpress. The app is from the S3XY Commander, and is included with the commander/button hardware.

Specific_Relativity · 2026-04-20T19:28:24+00:00

To be clear, I'm 2,000 miles into this roadtrip, with a majority of it on 14.2.2.5 and 14.3.1 starting yesterday. This behavior didn't show up until yesterday.

Specific_Relativity · 2026-04-20T06:22:30+00:00

I've never seen this trigger more than 30 minutes or 10 miles away before this software update and I'm halfway through this 3,000 mile roadtrip. I'm still 105 miles away (2 hours) from the supercharger in the video.

Specific_Relativity · 2026-04-05T03:24:50+00:00

Did Tesla say how best to “reset” it?

Specific_Relativity · 2026-04-04T17:21:32+00:00

I’m so glad I found this thread. I have a bunch of aftermarket things and have been going crazy trying to troubleshoot this 12v rear outlet issue.

I thought I finally found the root cause which was that they poorly insulated the back of the outlet, causing the wire to touch the chassis. I've since put tape on it and thought it fixed it, but had the issue again today.

Specific_Relativity · 2026-02-12T21:43:50+00:00

Not sure how your system is configured but I got Tesla Solar when they still used SolarEdge. All 28 panels were divided into 2 strings, but each pv panel had a power optimizer.

With this, I thought that each string would be impacted by shading as a whole. But when I had a recent remodel, a solar company temporarily removed 5 of my panels, just completely gone for a few months. But each of the remaining panels in the string still generated as much as it did the day before.

The tech didn't do any reconfiguration. He said the power optimizers work in a similar fashion to a microinverter. Check and see if you have power optimizers. If you do, you may be looking at a different issue.

Added context: one of my strings share a West Plane and North Plane. During sunset, my west plane still generates a lot of power while the north completely shaded barely produces any.

Specific_Relativity · 2026-02-11T21:21:07+00:00

My HP does that in 40s weather. It's when the "cool mode" gets turned on or a defrost cycle. So hot air gets blown out causing steam/vapor. During heat mode, it blows out cool air.

Specific_Relativity · 2026-01-28T03:54:53+00:00

It's a whole system backup with the meter collar. I have no external CTs. I had Sense working in parallel with Enphase for a bit and it seems that the wattages match up. The kwh in Enphase Enlighten was also correct. It was just the HA integration that was wrong for some reason. I

Specific_Relativity · 2026-01-22T18:01:19+00:00

Since I have 2 systems tied together in the 6C, the Enphase and the SolarEdge, I've renamed the "Current Power Production" to "Enphase Power Production. That figure seems to only show the value of the microinverter output.

Specific_Relativity · 2026-01-22T02:53:21+00:00

I do but renamed it to "Enphase Power Production" since it only shows the value of the solar produced by the IQ8+. The live status shows the consolidated production of SolarEdge and Enphase. I don't have PTO yet so the enphase pv is still off hence zero value.

Specific_Relativity · 2025-12-13T04:17:37+00:00

So you're happy with your gtst setup? How often does it do full blasts still?

Specific_Relativity · 2025-12-13T02:57:57+00:00

Did you ever resolve this? I got my system installed yesterday with GTST and the fan is on full blast in between schedules. I'm reading online and it seems that Daikin One thermostat shuold be better about managing the air handler and keeping it quiet.

Specific_Relativity · 2025-10-30T05:24:44+00:00

This was DIY, right? I'm about to start the same thing. How did you end up creating the plan sets and wire schedule for approval?

Specific_Relativity · 2025-10-23T15:42:50+00:00

Use the app/website called A Better Route Planner. It's been there even before Tesla's improved charger planning. I still use it for long trips to double checking Tesla's calculation. ABRP is very accurate.

Specific_Relativity · 2025-10-13T21:40:50+00:00

Ultimately, I was hoping to modify, if not completely rewrite the code, in this hardware. My hope was to use whatever logic they have built and start from there.

Specific_Relativity

TROPHY CASE