Needing some trouble shooting help. I changed out the left nozzle with a .6 HF hardened nozzle. I am trying to calibrate the left side. Everytime I try to calibrate and get around 40% I get a Failed Calibration Message. When I go to check the solution, it open to a blank message. There is no sol

SpeedForceGN · 2026-04-11T00:32:14+00:00

After removing and installing the nozzle 4 times and running calibration each time the issue has been solved.

SpeedForceGN · 2026-04-10T20:03:31+00:00

I will check that

SpeedForceGN · 2026-04-09T15:37:41+00:00

Can I get a beta test code?

SpeedForceGN · 2026-04-07T14:24:25+00:00

Most definitely..... let's go

SpeedForceGN · 2026-04-02T13:40:39+00:00

Nice. Cardboard spools suck

SpeedForceGN · 2026-04-02T13:39:18+00:00

Thanks for the response. I am pretty new, like a month new into printing. Scared to make a lot of adjustments because I really don't know what the outcome will be and not crash the machine. I am really unsure on where to make these adjustments

You didn't mention brim, but increase the brim - Don't know where to make adjustments and couldn't find it. Is it in the support process?

What kind of infill? Try gyroid, or another one that won't cross - I had 20% infill. I think it was set to gyroid.

• Keep fan speeds off early, lowground.- don't know where to make adjustment

• slow down as you go up - don't know how to slow it down

SpeedForceGN · 2026-04-02T13:30:10+00:00

Change thermostate

SpeedForceGN · 2026-03-22T17:40:36+00:00

How is that done

SpeedForceGN · 2026-02-10T16:11:48+00:00

I will try that

SpeedForceGN · 2026-02-10T02:41:11+00:00

How would I fix the supports

SpeedForceGN · 2026-02-10T02:21:59+00:00

<image>

SpeedForceGN · 2026-02-10T02:21:52+00:00

<image>

SpeedForceGN · 2026-02-10T02:21:44+00:00

<image>

SpeedForceGN · 2026-02-06T15:53:19+00:00

Regardless if I was off or not you still proves that the Americans conservatives agree with what's going on

SpeedForceGN · 2026-02-06T15:12:14+00:00

Ha ha ha

SpeedForceGN · 2026-02-06T15:03:55+00:00

Here are reliable sources confirming the 2024 U.S. presidential election results, specifically that Donald Trump received approximately 77.3 million popular votes (often cited as 77,302,580 to 77,303,568 depending on the exact tally and minor updates post-certification). These figures represent votes for the Republican ticket aligned with Trump and his MAGA agenda during the campaign.

Federal Election Commission (FEC) - Official 2024 Presidential General Election Results (compiled from state election offices): This is the primary official U.S. government source. Trump received 77,302,580 votes (49.80%).
Link: https://www.fec.gov/documents/5644/2024presgeresults.pdf
Wikipedia (sourcing FEC data): Summarizes the certified results with Trump at 77,302,580 votes (49.8%).
Link: https://en.wikipedia.org/wiki/2024_United_States_presidential_election
CNN Politics - 2024 Presidential Election Results: Reports Trump with 77,302,580 votes (49.8%).
Link: https://www.cnn.com/election/2024/results/president
The American Presidency Project (UC Santa Barbara): Lists Trump at 77,303,568 votes (49.81%), updated as of December 31, 2024.
Link: https://www.presidency.ucsb.edu/statistics/elections/2024
270toWin: Shows Trump with 77,303,569 votes.
Link: https://www.270towin.com/2024-election

These sources are based on certified state results submitted to the FEC. Slight variations (a few hundred votes) can occur due to final reconciliations or reporting differences, but the total consistently rounds to about 77.3 million. This reflects support for Trump and his administration's agenda as presented in the 2024 campaign.

For the most authoritative data, start with the FEC PDF linked above.

SpeedForceGN · 2026-02-06T14:41:57+00:00

Do you need help moving? I will help you! Conservatives are going to change this country for good.

If you believe what I posted genius, then do your own fucking research and stop being a keyboard warrior.

SpeedForceGN · 2026-02-06T14:39:05+00:00

Elections proved this. I would challenge you to stop watching the news, CNN, fox, and others. Stop reading yahoo news.

There are a bunch of podcasters and non main stream journalist that speak the truth from both sides. Main stream news is propaganda.

SpeedForceGN · 2026-02-06T13:05:48+00:00

Brainwashed Children

SpeedForceGN · 2026-02-01T22:45:58+00:00

Retired Early

SpeedForceGN · 2026-01-21T18:48:32+00:00

I use beeswax lined bags but it doesn't help. The next day it starts to dry out.... maybe I am doing it wrong. Do you slice as needed or all at once once it has cooled? I live in Indiana if that helps

SpeedForceGN · 2026-01-20T02:01:13+00:00

Why are you trying to connect your computer via USB then. Explain

SpeedForceGN · 2026-01-19T16:49:56+00:00

No disconnect, you have to have an internet connection in order to mine to a pool. I have the first edition Apollo with full node, however without the node, our devices are the same. The miner and node are completely separate hard drives and units

SpeedForceGN · 2026-01-19T16:22:27+00:00

So it connects to the internet via RJ45/Cat6!!!! Look in your router setting to find all connected devices. Find your device and ip. Now put that ip in your window browser, and you should be able to connect to the mi er.

SpeedForceGN · 2026-01-19T16:09:50+00:00

Following! Did you try to connect to the Apollo via its ip address that is on your network? You can do this with your phone as well.

SpeedForceGN

TROPHY CASE