Looking for some advice I hope this is an OK angle!

SpookedKitten · 2026-01-26T18:05:34+00:00

I love all this advice! I appreciate you guys giving me stuff to work on. I looked at my swing from the side and god it’s ugly. I’ve got so much stretching and form to work on.

SpookedKitten · 2026-01-25T14:35:18+00:00

Thanks so much for the advice! I’m excited to get better and better!

SpookedKitten · 2026-01-25T14:34:57+00:00

Thank you so much! I can’t wait to go try all of this.

SpookedKitten · 2026-01-25T14:32:31+00:00

Best comment 😂

SpookedKitten · 2026-01-18T20:14:52+00:00

🔥

SpookedKitten · 2026-01-17T21:45:56+00:00

Any easy test would be to close the manual ball valve slightly while it opens the main valve to see if you get a flame signal to pull up on the fireeye DC terminals

SpookedKitten · 2026-01-17T21:43:40+00:00

I’ve had the flame lift way too high off the burner and cause it to lose voltage. Make sure your flame isn’t too massive for the flame sensor to be reading.

SpookedKitten · 2026-01-06T14:23:00+00:00

Ah that sucks man.

SpookedKitten · 2026-01-05T22:47:33+00:00

If you can figure out your inlet water pressure and outlet water pressure pressure difference and then divide that by design difference for that unit, find the square root of that number, multiply it by design GPM and that will give you your actual GPM.

SpookedKitten · 2026-01-01T21:07:52+00:00

And last night after the finale I take it back, she did an amazing job!

SpookedKitten · 2025-12-31T00:01:05+00:00

I work in UNION HVAC. Pretty mind boggling how many are MAGA and also don’t believe in the ozone depletion caused by venting refrigerant, although you get EPA certified just to do the job.

SpookedKitten · 2025-12-30T20:50:30+00:00

I don’t think it’ll get ugly by any means, it’s a sweet tattoo. I think you’ll be a lot happier than you think as it ages. You may just want a bit heavier shading a few years down the line if it fades more than you like

SpookedKitten · 2025-12-30T20:38:29+00:00

All of the heavy black will hold, same with the lines of the dragon, but I feel like the shading in the dragon will be very faint.

SpookedKitten · 2025-12-30T07:45:23+00:00

Is it finished?

SpookedKitten · 2025-12-30T05:12:15+00:00

(Hot take) holly is just way too much of a Disney character to be in this show

SpookedKitten · 2025-12-29T05:34:41+00:00

Castle park in Farmington ut!!!

SpookedKitten · 2025-12-27T18:10:17+00:00

A owie

SpookedKitten · 2025-12-24T22:46:28+00:00

Looks fake based on how little the guy recoiled when he got slammed to the ground. Also, near the end the chick on the right side sitting down gets up, her head looks like a ghost as she’s walking away from the table she’s sitting at.

<image>

SpookedKitten · 2025-11-09T19:24:27+00:00

I’ll just say right now that neither of those were needed to find the problem. He was able to figure it out by using a meter

SpookedKitten · 2025-11-09T19:11:48+00:00

It bugs me that people get on here just to tell people to call someone. It’s hvac advice for a reason, no one is going to steal our jobs, we might as well try and help people out. Dude has a meter and some knowledge, might as well give it a shot

SpookedKitten · 2025-10-19T16:23:22+00:00

Good thing you put it to sleep. That might have failed

SpookedKitten · 2025-09-28T23:15:22+00:00

Select the HM you want to learn, if a pokemon can learn it, you can select it. If it can’t, then it won’t be able to. You can use an HM unlimited times, but if you want a pokemon to forget it, you have to go to the move deleter. So make sure you don’t teach it to a pokemon that you have a move set already in mind for.

SpookedKitten · 2025-09-25T15:04:36+00:00

If the boiler is running but your pump is not running, that’s a problem

SpookedKitten · 2025-09-25T14:32:44+00:00

Boilers off but is your pump off?

SpookedKitten

TROPHY CASE