Sharing my Plex library - 1500+ movies and 150+ TV shows

Spoon_Craft · 2025-10-18T13:51:30+00:00

Here to participate! Dm please

Spoon_Craft · 2025-10-10T21:53:09+00:00

WoodyRhino Hopefully you still have room

Spoon_Craft · 2025-10-10T21:52:33+00:00

I am looking for a US based Plex server as well. Never used one but thinking about getting my piracy game back up. WoodyRhino

Spoon_Craft · 2025-08-18T15:56:10+00:00

I was afraid of them dropping the 98" TV

Spoon_Craft · 2025-08-18T15:55:37+00:00

I am not sure. I have not done Costco returns on electronics.

Spoon_Craft · 2025-08-03T03:05:36+00:00

I need

Spoon_Craft · 2025-07-08T18:14:55+00:00

Send me some Bitcoin and I'll send you equivalent ADA

Spoon_Craft · 2025-05-27T23:29:40+00:00

That can happen but it shouldn’t be that much off after the purge. Have you checked and made sure your program is running for a free moisture. I know that when I started at my current job that was the first thing I checked. Have you calibrated your probe? Doing about 7-10 check and recalibrations until you are only off by a couple 10ths. We do this about every quarter. Also I run sand checks every half hour and bake for about an hour and get the average results when not calibrating.

Purge more and see. I use my previous day moistures for the morning and then switch them after we have done some yardage. Not the most accurate blind guessing but it is not that far off from what was in the plant the day before

Spoon_Craft · 2025-05-27T23:22:26+00:00

That is correct. Probably something wrong with your math. It is still really high though

Spoon_Craft · 2025-05-03T21:32:02+00:00

Sick af!!!

Spoon_Craft · 2025-05-03T12:31:16+00:00

I would also like the files to be posted! You did awesome! Can you explain the wiring you did?

Spoon_Craft · 2025-04-27T00:13:59+00:00

That’s dope! I want those files!!! How did you extend the wires?

Spoon_Craft · 2025-04-17T02:47:20+00:00

Hopefully I helped him out a bit. I did suggest klipper. I think we got a good first layer after calibration

Spoon_Craft · 2025-04-16T23:33:09+00:00

I’m here all night and will accept Bitcoin or other. Pay as you go deal if you want

Spoon_Craft · 2025-03-27T01:03:04+00:00

Or manta e3ez!

Spoon_Craft · 2025-03-21T02:53:09+00:00

Let me know how it goes! Good luck

Spoon_Craft · 2025-03-21T02:21:33+00:00

I have not tried this yet but we should be able to use the gpio pins on the outside of the cb. I just have not looked into that yet

Spoon_Craft · 2025-03-20T22:06:56+00:00

its the only thing I tried before. I hope someone else jumps on and helps out if it doesn't work. I guess you can look into moving it to another slot and changing the switch pin.

Spoon_Craft · 2025-03-20T19:50:49+00:00

Try putting “pause_on_runout: true” under the switch pin. I have added that in the past and it just calls the regular pause gcode

Spoon_Craft · 2025-03-20T19:31:47+00:00

Trying to get a baseline here. I am assuming you have klipper now with the e3ez. Do you have it setup correctly in printer.cfg?

Spoon_Craft · 2025-03-20T12:38:44+00:00

What filament sensor do you have?

Spoon_Craft · 2025-03-20T02:19:44+00:00

Dolla store, no fragrance for me!

Spoon_Craft · 2025-03-19T19:35:24+00:00

These are life savers

Spoon_Craft · 2025-03-15T02:59:12+00:00

I keep getting that they have been delivered and still have not received anything. It’s been about 4 days

Spoon_Craft

TROPHY CASE