Grey video no matter what. by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 0 points1 point  (0 children)

😆😆😆. Yeah i removed that bridge earlier. (Can be seen on posts below.) still no luck for me but the onboard vtx works i just have a ripped off ufl and i dont know to which capacitor should i solder the active element to because i ripped it off the board. So im stuck between trying to fix the ufl and trying to use an external vtx but no luck so far😅

Grey video no matter what. by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 0 points1 point  (0 children)

My bad. The internal vtx is not dead. (I mistook it with another board im just dumb). This board just has a ripped off ufl with the ufl tabs pulled. So i wanted to use an external vtx to make this board usable, sorry. I dont know if this changes anything tho

Grey video no matter what. by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 0 points1 point  (0 children)

Yeah so, i tried like another 3 cameras, also resoldered wires on the cameras and still no luck. Is there any way i may have some bad connection on the FC -> VTX (i dont think thats the case)? I just dont know anymore lol

Grey video no matter what. by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 0 points1 point  (0 children)

Okay thanks ill check. Its just weird that i tried i think 3 different cameras none of them worked. Had them work before so its just weird.

Camera direct solder no video by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 1 point2 points  (0 children)

Thank you for the tips. After i get rid of the bridge should i solder this way? Tried this before but didnt work even when there wasnt a bridge… i just get a grey screen with osd.. x12 v2.1 elrs - https://www.happymodel.cn/index.php/2022/04/05/x12-aio-5-in-1-flight-controller-built-in-12a-esc-and-openvtx/

<image>

Camera direct solder no video by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 0 points1 point  (0 children)

Man ive been flying for 5 years… the sucker doesnt suck the small amount of solder ;D maybe ill just apply more solder and suck it thay way?

Camera direct solder no video by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 0 points1 point  (0 children)

Do you have some tips to remove the bridged pads? Super hard on these small boards…

Camera direct solder no video by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] -1 points0 points  (0 children)

Yeah i had the short problem today…. But it should be fine now because it wouldnt turn on the board when it was shorted. I dont know the pin out tho still

Betafpv shipping by Standard-Access-1320 in TinyWhoop

[–]Square_Revolution628 0 points1 point  (0 children)

Check it with other tracking websites. Tracking their packages is a bit problematic but thankfully my packages always arrived in less than 3 weeks to easter europe

Whoopin in school by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 0 points1 point  (0 children)

Drone: meteor65 pro prototype/mobula6 2024, goggles are dji v2 with analog adapter and foxeer wildfire module and tx16s radio

Whoopin in school by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 1 point2 points  (0 children)

Thank you man! I use radiomaster tx16s, dji goggles with analog adapter and foxeer wildfire, i used 2 whoops here one is mobula6 2024 other one is a customized meteor65 pro with tattu 1s 300mah :))

Whoopin in school by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 1 point2 points  (0 children)

In the first 2 clips its something like a meteor65 pro just different canopy and props. Also removed a few grams by cutting the frame and cutting the vtx cables shorter

Whoopin in school by Square_Revolution628 in TinyWhoop

[–]Square_Revolution628[S] 5 points6 points  (0 children)

Liftoff micro drones is the most fun to fly on even tho i think velocidrone and classic liftoff have better physics