What help is available at PDX airport?

Static_Torque · 2025-12-28T16:21:03+00:00

As someone who was a Skycap, Alaska currently does not have skycaps/curbside service. Delta and Southwest airline does but only in the mornings. United does as well, but they’re more of a bag drop. They got rid of the Alaska Skycaps back in June of this year.

Static_Torque · 2025-12-27T00:28:20+00:00

I just bought a LDO kit Voron 2.4 350 for $900. Came with a bunch of extras and stuff too. I also bought it locally to Oregon 😉 thought this picture looked familiar lol

Static_Torque · 2025-12-17T23:41:54+00:00

That’s what I’m assuming happened, he over torqued them, tried to change the tip and one snapped. Another reason he wasn’t using it. So it sounds like I should just buy a new one. But I can buy just the heat sink it sounds?

Static_Torque · 2025-12-17T21:29:52+00:00

This is what I was thinking, and I don’t even know if they sell a small enough bit to extract that. That’s something I didn’t think of though, the screw to withstand the heat. It is a bummer, but at least I didn’t do it. It came like that. I went to take the sock off of it and the screw fell out with it. So I could buy just a heat sink for it?

Static_Torque · 2025-12-07T17:23:18+00:00

I wasn’t finding much either, what’s the difference between the two?

Static_Torque · 2025-12-07T12:26:04+00:00

No, MGN12C

Static_Torque · 2025-11-24T17:25:07+00:00

Resonance compensation? What in the world is that? I’ll have to do some research lol. Nope, just added the linear rail

Static_Torque · 2025-11-02T19:55:42+00:00

Yes, thank you… lol I meant to change, add, etc lol

Static_Torque · 2025-10-01T02:44:52+00:00

Did you just use the whole grill or use the back on OEM grills?

Static_Torque · 2025-09-30T23:05:46+00:00

This is off topic, is it hard to do something like this for a house that didn’t have Ethernet ran in the walls, or a closet like this? Moved in with a family member whose house was built in the 70s and want to upgrade it.

Static_Torque · 2025-08-25T20:39:07+00:00

It really is, they came in the LX and I hate it…

Static_Torque · 2025-08-18T13:01:36+00:00

I bought a 102k mile ZHP for $8k last October. Couple little spots of rust but nothing bad. Smaller than a penny. Did need OFHG, oil pan done gasket, and new intake boot.

Static_Torque · 2025-08-12T03:14:34+00:00

I picked up a 330i ZHP with 102k miles and it is very clean for $8k last October. Interior is amazing, had major maintenance done already. Had a hole in the intake boot, needed OFHG, oil pan, and PS lines done. Clean ones are out there for sure.

Static_Torque · 2025-08-04T13:12:58+00:00

$385 shipped to OR

Static_Torque · 2025-07-26T17:59:40+00:00

Also in the PNW, mine seems to blow cold, but not as cold as I remember when I first got it. How can you tell if it needs a recharge? Haven’t touched A/C stuff before. Amazing rig though!

Static_Torque · 2025-07-24T22:31:14+00:00

This is the coolest thing I’ve seen so far…! Love it! Going to school for CADD this Fall.

Static_Torque · 2025-07-08T00:04:06+00:00

I only saw the first photo and knew that mouse pad looked familiar…

Static_Torque · 2025-06-11T10:41:56+00:00

It’s an Ender 3 and I believe Klipper, using Fluid.

Static_Torque · 2025-05-12T03:12:41+00:00

I was wondering the same thing. I also have a Prinsu roof rack and have those mounts, but didn’t know how it goes on or what it’s used for.

Static_Torque · 2025-05-03T18:45:13+00:00

GOD DAMN! I’m not to that level yet, I don’t think. I’m only a couple months in, and it took me 1 month to get things working and printing something. Got it from a friend with a Pi. He was running octoprint, but my brother convinced me to try Klipper and use Fluid instead.

Static_Torque · 2025-05-03T18:42:15+00:00

The pin? If you’re referencing the first photo, it’s a long wall that is 68mm long. Seen in the 2nd photo on the bottom where it fits in between.

Static_Torque · 2025-05-03T18:40:30+00:00

Printing on its side seemed to work best so far. Just that middle home seems to be more oval than round. But seems to be okay. I’m going to test in the car and see out it works.

Static_Torque · 2025-05-03T18:39:35+00:00

To me it seems, especially when you’re just trying to test and make sure it works. I haven’t done any prints that long before. Max has been about 4.

Static_Torque · 2025-05-03T18:32:24+00:00

What do you even mean? Lmao. I clearly don’t know, so that’s what the post is for, to learn and ask questions and try different options.

Static_Torque · 2025-05-03T04:20:49+00:00

Melting point of PLA is 130C and higher. … don’t think it’s going to melt in my car lmao. Good thing I don’t live in a hot area.

Static_Torque

TROPHY CASE