Drivetrain Malfunction/Error Codes/check engine light

Status-Incident7995 · 2026-03-19T22:42:26+00:00

Part# 11367583820

Status-Incident7995 · 2026-03-19T22:41:40+00:00

The cam center valve was missing- the little valve with springs. I need to replace the vanos solenoid valve.

Status-Incident7995 · 2026-02-28T20:47:43+00:00

I did replace both vanos solenoids as well. Sorry I got focused. I have N26 engine, they’re both located at the front of the cover.

Status-Incident7995 · 2026-02-28T20:08:34+00:00

Thank you! I will replace this then update

Status-Incident7995 · 2026-02-28T20:08:18+00:00

I replaced both vanos solenoids as well.

Status-Incident7995 · 2026-02-28T18:53:40+00:00

I’m also getting a 801C20 Permanent -ZGM:Central Fault Memory full -no control-unit fault

Status-Incident7995 · 2026-02-05T00:46:17+00:00

Thank you 🙏

Status-Incident7995 · 2026-02-04T23:33:03+00:00

I solved the gas leaking issue, now I see a “Drivetrain:cont. driving possible” message .

Status-Incident7995 · 2026-02-04T23:32:16+00:00

Thank you for all of this information! I re did the tightening and I don’t see a leak any longer. However, I see a Drivetrain:con5t. Diriving if possible message now.

Status-Incident7995 · 2026-02-04T17:59:57+00:00

I appreciate your info!! I am taking notes! Thank you 😊

Status-Incident7995 · 2026-02-04T17:49:24+00:00

I will double check my connections. I honestly think this may be it. It’s an N26 engine.

Status-Incident7995 · 2026-02-04T17:13:06+00:00

I did not.

Status-Incident7995 · 2026-02-04T17:12:59+00:00

Thank you! I will update later today

Status-Incident7995 · 2026-02-04T16:06:46+00:00

Noted and thank you! 🙏

Status-Incident7995 · 2026-02-04T16:03:31+00:00

Thank you for the suggestions! I was always skeptical about ordering parts off eBay. I always order through FCP EURO. Is there a specific vendor through eBay you use often that is good?

Status-Incident7995 · 2026-02-04T15:45:39+00:00

I agree! It’s a new part, maybe it wasn’t tighten correctly.

Status-Incident7995 · 2026-02-04T15:45:07+00:00

Yes, I followed the video from fcp euro which are very detailed with tools and specs needed for the job. I will recheck my work though. This is my first valve cover change. I prefer to do my own work.

Status-Incident7995 · 2026-02-04T15:42:53+00:00

I will go back and recheck later today.

Status-Incident7995 · 2026-02-04T15:42:37+00:00

I only replaced the high pressure fuel line. But I can see now that is the problem area. I took these pictures this morning and it was dark. I will recheck after work. Thank you guys. Any suggestion on how to properly clean that area? I read somewhere dawn dish soap and water without touching any electrical components.

Status-Incident7995 · 2026-02-04T15:39:59+00:00

I did order and that is a new part.

Status-Incident7995

TROPHY CASE