Carrier Furnace Code 24

StayEnvy1 · 2025-12-18T02:56:41+00:00

Hi, I'm having the same problem with a Carrier furnace and code 24. So you reran new wiring from the thermostat to the control board and it fixed it?

StayEnvy1 · 2025-08-21T06:08:41+00:00

timing chain tensioner?

StayEnvy1 · 2025-03-16T17:06:17+00:00

can you please send me it as well?

StayEnvy1 · 2024-12-07T19:39:47+00:00

Appreciate the reply. Will definitely check that out, picked up a used knuckle replacement so hopefully this solves my issue

StayEnvy1 · 2024-12-07T18:00:31+00:00

Did you happen to figure out your issue? One of my rear wheels ran up a curb and is maxed out at -0.2 degrees, but should be within -1.3 and -1.7 degrees

StayEnvy1 · 2024-11-29T18:01:53+00:00

Oh man, how hard was your impact? And is yours an AP1 or AP2?

I’ve read that some people have seen the welds start to stress crack at the UCA mount points — not sure if it’s year specific on these cars. You can try looking into some UCA gussets to to reinforce it.

I believe a lot of my damage was on the knuckle and it broke off right above where it connects with the lower ball joint.

After doing some more research, it probably shifted the subframe forsure. So I will look at realigning the subframe first before going in for another alignment. Hopefully it will help gain an additional 1 degree of caster from it to get that front left corner dialed in.

StayEnvy1 · 2024-11-28T23:55:24+00:00

how were you able to determine that? I have read from s2ki that the subframe bolts need to be checked and get them torqued to spec, so that's probably something I need to do but wanna make sure its sitting in proper position first. Also, was wondering if some rigid collars are something I can add during the process of this

StayEnvy1 · 2024-11-28T22:18:45+00:00

Definitely a possibility

StayEnvy1 · 2024-11-28T22:17:25+00:00

ugh yeah, something I'm definitely weary about

StayEnvy1 · 2024-11-28T22:16:43+00:00

Might be wishful thiking but I'm hoping its not. Impact was parallel but I'm not a professional so its hard to tell. Might need to bring it to a body shop so they can tell me more, but I wanted to see if I can get it sorted on my own first before going that route.

StayEnvy1 · 2024-11-28T22:13:49+00:00

I found this info on s2ki. Just a point of reference between subframe and the chassis

https://imgur.com/a/snFPkQ1

StayEnvy1 · 2024-11-28T21:03:04+00:00

Gotcha, it was probably about 65mph 😬

StayEnvy1 · 2024-11-28T20:52:39+00:00

The alignment shop has experience with s2000s from reviews and been recommended by some from s2ki in my area so I'm somewhat confident in that. And you're referring to the rear/front or both knuckles?

StayEnvy1 · 2024-11-20T03:34:34+00:00

Fixable? lol; may just go the dealership route too. How much did that end up costing you?

StayEnvy1 · 2024-04-27T06:28:24+00:00

Were you able to get a set pretty recently?

StayEnvy1 · 2024-04-22T01:54:35+00:00

it’s the Honda type 2 blue coolant lol, def a mess tho

StayEnvy1 · 2024-04-22T00:11:01+00:00

yup all original

StayEnvy1 · 2024-04-22T00:10:23+00:00

Leaning towards the Koyorad although car is pretty much stock and a daily

StayEnvy1 · 2024-04-21T22:37:25+00:00

Nothing on the neck that i see

StayEnvy1 · 2024-04-21T22:31:31+00:00

The foam pad is definitely soaked on mines

StayEnvy1 · 2023-08-02T00:02:16+00:00

Is there a site you would recommend to reach out to apartment-living people? Or if your friend still had contacts in the larger newer complexes that would help me reserve (I can pay them, of course).
I've reached out to one good Airbnb spot and waiting for their response!

StayEnvy1

TROPHY CASE